Smarteh LPC-2.DT1B Operation & User’s Manual

LPC-2.DT1B Light Switch Control panel Version 1 SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: +386(0)5 388 44 00 / e-mail: [email protected] / www.smarteh.si ...

Written by SMARTEH d.o.o. Copyright © 2013, SMARTEH d.o.o. User Manual Document Version: 001 September 1, 2013 i ...

STANDARDS AND PROVISIONS: Standards, recommendations, regulations and provisions of the country in which the devices will operate, must be considered while planning and setting up electrical devices. Work on 230 V AC network is allowed for authorized personnel only. DANGER WARNINGS: Devices or modules must be protected from moisture, dirt and damage during transport, storing and operation. WARR ...

Longo programmable controller LPC-2.DT1B 1 DESCRIPTION...................................................................................1 2 FEATURES.......................................................................................2 3 OPERATION.....................................................................................3 3.1 Operational modes.............................................................. ...

1 DESCRIPTION LPC-2.DT1B control panel (CP) is used to switch on and off four individual or group of lights. Panel is equipped with four push buttons (PB), temperature sensor and light intensity sensor. To switch on or off individual or group of lights , corresponding PB should be pressed respectively. For example if first light is switched off, light symbol next to PB1 on LCD will represent off status. After PB1 ...

2 FEATURES Figure 1: LPC-2.DT1B module. Table 1: Features 4 touch buttons to switch light on/off 4 light symbols to show lights on/off status Temperature measurement Light intensity measurement LCD intensity control Color LCD with possibility of back ground picture changing1 1 For LCD background picture replacement, please refer to LCD Composer → Help . 2 ...

3 OPERATION Basic switching can be done with panel Push Buttons (PB).Modes of operation and commands can be set via LPC Manager software. It is advised to press touch-buttons respectively with finger not faster than 1 press per second. Press should be done with whole finger tip. Brief pressing could not activate the action, because of protection against the noise and other influence. 3.1 Operational modes Normal mod ...

Actual temp.: Actual room temperature 0 .. 5000 represents 0.00 .. 50.00 °C. Actual light: Actual room light intensity 0 .. 100 represents 0 .. 100%. Light x (Off/On) command: remote On/Off command for individual light. This command is enabled using corresponding Light x (Local/Remote) command. Light x (Local/Remote) command: Enables corresponding light On/Off remote command. Clock display enable command: Time Clo ...

4 INSTALLATION 4.1 Connection scheme Figure 2: Connection scheme 5 ...

Table 2: K1 K1.1 GND Ground K1.2 7 .. 30 V DC Power supply input K1.3 Standard RS-485 A Data receive/send line A K1.4 Standard RS-485 B Data receive/send line B Table 3: LCD bars & Buttons PB1 (Up-left) Light 1 Switch light 1 on/off, status is shown on LCD next to PB1 PB2 (Down-left) Light 2 Switch light 2 on/off, status is shown on LCD next to PB2 PB3 (Up-right) Light 3 Switch light 3 on/off, status is shown on LCD ...

4.2 Mounting frame selection Smarteh has verified following lines to be compatible with LPC-2.DT1B module: ● Bticino – Living, Light ● Gewiss – Playbus, System ● Vimar – Plana, Idea ● Tem – Modul Soft, Modul Line ● Master Frames of other vendors most probably suits as well, but they were not verified by Smarteh. Before installation verify compatibility of non listed frames. Module housing has a fin ...

4.3 Mounting instructions Figure 3: Housing dimensions Dimensions in milimeters. All connections, module attachments and assembling must be done while module is not connected to the main power supply. Module should be positioned in the wall inside of the room. Avoid direct sunlight or positioning near heating/cooling source object. Usage of cover frames and holders made of metal, could cause the decreased performanc ...

4.4 Module labeling Figure 5: Labels Label 1: Label 2: Label 1 description: • LPC-2.DT1B is the full product name • P/N: 225DT1B10V01001 is the part number • 225 – general code for LPC-2 product family, • DT1 – short product name, • 10 – year of code opening, • V - denotes flush frame mounting module, • 01 – derivation code, • 001 – version code (reserved for future HW and/or SW firmware up ...

5 TECHNICAL SPECIFICATIONS Table 5: Technical specifications Power supply from MCU Interconnection connector type RJ-12 6/6 Power consumption 1 W Dimensions (W x H x D) 75 x 49 x 29 mm Weight 50 g Maximum altitude 2000 m Mounting position horizontal Ambient temperature 0 to 50 °C Ambient humidity max. 95 %, no condensation Transport and storage temperature -20 to 60 °C Protection class IP 20 10 ...

6 CHANGES The following table describes all the changes to the document. Date V. Description 1.9.2013 001 The initial version, issued as LPC-2.DT1B module UserManual. 11 ...