Zenith 2190SS Assembly Instructions Manual

Text of Zenith 2190SS Assembly Instructions Manual

Pg 1 of 8

©2011 Zenith Products Corp. Assembly Instructions - Model 2190SS (Chrome) Instrucciones de Ensamblado - Modelo Model 2190SS (Cromo) Instructions d’assemblage – Modèle 2190SS (Chrome) IS2190-I MCS 1/24/2011 Before You Begin: Thank you for purchasing this product. Please identify all parts and hardware pieces before you begin. When laying out parts, place them on a soft surface to prevent scratching. If any pieces are missing, call our Toll F

Pg 2 of 8

(C) 2 Short tapered tubes 2 Tubos afilados cortocircuito 2 tubes coniques courts (H) 1 Small end cap 1 Cubierta terminal pequeña 1 petit embout (F) 4 Wedges 4 Anillos de soporte 4 clavettes (B) 2 Long tapered tubes 2 Tubos largos con ahusamiento 2 longs tubes coniques (G) 2 Tape Strips 2 Tiras de Cinta 2 bandes adhésives IS2190-I (I) 1 Large end cap 1 Cubierta terminal grande 1 gros embout (D) 3 Shallow Wire Shelves 3 Repisas alámbricas poco

Pg 3 of 8

1. IS2190-I D D F F B tapered end at the bottom el extremo con ahusamiento en la parte inferior extrémité conique en bas Place a wedge (F) (tapered or rounded end up) on one of the long tapered tubes (B) approximately half way down. Slide shallow wire shelf (D) down the tube and fit over the wedge. Repeat process for other shallow wire shelf (D). Shelves can be adjusted by moving the wedges up or down. Coloque una cuña (F) (ahusada o con el ex

Pg 4 of 8

2. D B IS2190-I F E tapered end at the bottom el extremo con ahusamiento en la parte inferior extrémité conique en bas Place a wedge (F) (tapered or rounded end up) on one of the long tapered tubes (B) approximately half way down. Slide deep wire shelf (E) down the tube and fit over the wedge. Repeat process for a shallow wire shelf (D). Shelves can be adjusted by moving the wedges up or down. Coloque una cuña (F) (ahusada o con el extremo red

Pg 5 of 8

3. upper tube assembly ensamble del tubo superior unité tubulaire supérieure lower tube assembly ensamble del tubo inferior unité tubulaire inférieure IS2190-I Place the tapered end of the tube with the two shelves on it into the untapered end of the other tube with the shelves on it. Coloque el extremo con ahusamiento del tubo con las dos repisas dentro del extremo sin ahusamiento del tubo con el ensamble de gabinete en él. Enfilez l'extré

Pg 6 of 8

A B A top superiore haut Place the tapered end of the long tapered tube (B) on top of the twist tube (A). Place the large end cap (I) on the bottom of twist tube (A). Coloque el extremo ahusado del tubo corto ahusado (B) en la parte superior del tubo de enroscar (A). Coloque la cubierta terminal grande (I) en la parte inferior del tubo de enroscar (A). Enfilez l’extrémité conique du long tube conique (B) dans le tube de torsion (A

Pg 7 of 8

5. IS2190-I Place the tapered end of the short tapered tube (C) into untapered end of the upper tube assembly. Place the small end cap (H) on the short tapered tube (C) NOTE: If the assembly will be installed on a tub ledge, first place the tube assembly on the tub ledge and measure the distance between the top tube and the ceiling. NOTE: If this distance is greater than 16 in., one short tapered tube (C) should be added to the top of the assembl

Pg 8 of 8

IS2190-I 7.Place the tape strips (G) around the seams of the tubes. (This will protect the tubes from moisture.) Coloque las tiras de cinta (G) alrededor de las uniones de los tubos. (Esto protegerá a los tubos de la humedad). Placez les bandes adhésives (G) autour des jointures de tubes (pour protéger ces derniers contre l'humidité). 6.Adjust twist tube (A) clockwise to increase the assembly height or turn counterclockwise to decrease the as

Zenith Indoor Furnishing Owners Instructions: