Turnstone Bivi Manual 

Text of Turnstone Bivi Manual 

Configuration de la table BiviMC et du système électrique

Configuração da mesa Bivi™ e sistema elétrico Configuración de la mesa BiviTM y sistema eléctrico ™ Table Configuration & Electrical System R © 2016 Steelcase Inc. Grand Rapids, MI 49501 U.S.A. Printed in U.S.A. (Included) (fourni) (incluído) Page 1 of 23 939500449 Rev J thumb screws Écrous à serrage à main parafusos manuais Tornillos de mano

1a. Install leg onto supports with four cap screws. Screws must

be securely tightened with no gaps between parts. Recommend tightening screws to 66-72 in-lbs. 1b. Install opposite leg same as previous step. 1c. Snap on covers. Page 2 of 23 939500449 Rev J ALIGN ROUND “TOP” LABELS. 1a 1b 1c 1d

Ensemble de pattes

1a. Fixez la patte au support au moyen de quatre vis d'assemblage. Les vis doivent être entièrement serrées, sans laisser d'espace entre les composantes. Le couple de serrage recommandé est de 66 à 72 po-lb. 1b. Installez l'autre patte comme indiqué à l'étape précédente. 1c. Enclenchez les couvercles. Page 3 of 23 939500449 Rev J ALIGNEZ LES ÉTIQUETTES RONDES “DANS LE HAUT” 1a 1b 1c 1d

Conjunto da perna

1a. Instale a perna sobre suportes com quatro parafusos sextavados. Os parafusos devem ser apertados com firmeza sem folgas entre as peças. Recomenda-se apertar os parafusos de 66 a 72 pol.-lbs. 1b. Instale a perna oposta da mesma forma descrita na etapa anterior. 1c. Encaixe nas tampas. Page 4 of 23 939500449 Rev J ALINHE OS RÓTULOS REDONDOS “SUPERIORES” 1a 1b 1c 1d

Ensamble de la pata

1a. Instale la pata sobre los soportes con cuatro tornillos de cabeza cilíndrica. Los tornillos deben estar bien apretados sin espacios entre las piezas. El apriete recomendado para los tornillos es 66-72 lbs-pulgs. 1b. Instale la pata opuesta igual al paso anterior. 1c. Cierre a presión las tapas. Page 5 of 23 939500449 Rev J ALINEE LAS ETIQUETAS REDONDAS “SUPERIORES” 1a 1b 1c 1d

2. Set the trough between the two

legs on a clean surface. Installation du passe-fil 2. Placez le passe-fil entre les deux pattes sur une surface propre. Calha em estágios 2. Posicione a calha entre as duas pernas em uma superfície limpa. Sitúe la artesa 2. Coloque la artesa entre las dos patas sobre una superficie limpia. Page 6 of 23 939500449 Rev J 2

Attach Leg to Trough

3. Stand one leg up, then lift and place end of electrical trough up to the leg. Drop the lip of the trough into the slot on the leg (3a). Make sure he connection bracket is fully engaged with the top leg slot (3b). Tighten with hex wrench (3c). TIPS: Rest one side of the trough on the floor and place lip on the other side into the bottom edge of the leg. Fixation de la patte au passe-fil 3. Mettez une des pattes debout, puis soulevez

Turnstone Indoor Furnishing Owners Instructions: