Triminator Shredmaster Owner's Manual

you to get the best results from your new shredder and to operate it safely. This manual contains the information on how to do that; please read it carefully before you set up and use your machine. This manual is intended for all ShredMaster machines in different configurations. If your equipment does not contain a component please disregard in ...

SAFETY WARNINGS ......................................................3 START-UP PROCEDURE ................................................4 CLEARING A JAM ...........................................................5 SHUT-DOWN PROCEDURE ..........................................5 MAINTENANCE & LUBRICATION ........... ...

a person under the equipment or in any dangerous position. • Using a lifting device with a minimum capacity of 3,000 pounds, remove the shredder from the carrier, and transport it to the installation site. 1. All internal wiring has been factory installed and tested prior to shipping. Electrical installation consists of pro ...

• Make sure that ALL guards, safety switches and access panels are in place at all times, EXCEPT when the power is locked off for maintenance work or cleaning. • ALWAYS know where emergency stop buttons are located. • ALWAYS know, or have quick access to, emergency phone numbers. • ALWAYS ensure that all maintenance and operating personnel read and ...

covers are in place. • Ensure the area is clean. • Check input conveyor for debris, discarded tools, etc. START-UP Plug power cable into installed receptacle. Depress momentarily the FORWARD pushbutton. Cutters will begin to rotate and the output conveyor will begin to run forward. To stop machine at any time depre ...

SHUT-DOWN PROCEDURE Should a jam occur, the machine will automatically go in the reverse direction for approximately two seconds, then after a brief pause the machine will automatically start in the forward direction. This forward and reverse automatic process will occur three times to clear the jam, if the machine remains jammed after the third cycle the machine will automatically turn itself off. 1. Ensure that all personnel are clear of ...

WEEKLY - EVERY 40 HOURS OF OPERATION • Inspect for any oil leaks around the spur gear oil bath or the gearbox reducers as applicable. • Confirm that all guards are correctly installed. MONTHLY - EVERY 160 HOURS OF OPERATION • Grease all bearings using a high-temperature #2 lithium based grease, 1-2 pumps per bearing. • Brush bearing grease on the spur gear teeth. • Spray oil on the chain & check chain tension. • Remo ...

200+Hrs Shell Omala S2-GX Synthetic Industrial Gear Oil Less than1 gallon total (Refer to Appendix 1) Chain Monthly Monthly Spur Gears Monthly Brush on Bearing Grease(Lithium) Main Roller Bearings (4) Weekly or every 20Hrs, whichever is less High-temperature #2 Lithium based Grease 1-2 Pumps Per Bearing ...

Cutter Stack tightness is factory set and should be checked if any of the following conditions exist: • Shred capacity drops noticeably. • Cutter Head becomes abnormally hot. • Unusual noise being generated from cutter head. • Noticeably large gap between two cutters. 1. Lock out machine power to prevent injury. ** Shut Down the Entire System and Lock Out the Power. Use proper lock Out and Tag Out Procedures **. 2. Remove ...

maintenance, or trouble-shooting. PROBLEM POSSIBLE CAUSE REMEDY Machine will not turn off using STOP buttons. Defective STOP button. Contacts burned together in reversing contactor. Check continuity (N.C.) If bad, replace. Check each leg of forward side of contactor for continuity. There should be no continuity. If there is, consult factory for replacement part. Machine will not run ...

but will not turn in either forward or reverse. One leg of the 3 phase power is dead (single phasing). Contacts burned in contactor and not making a connection on one leg. Defective motor. Remove each fuse. Check for continuity in the power supply and disconnect. Consult factory for replacement contactor. Consult factory for replacement motor. Overload tripping. Low voltage. Current relay set too high ...

REVERSE but will run in forward. Defective reverse button. Disconnected wire on reverse button. Defective coil in reverse side of contactor. Check for continuity. If bad, replace. Shredding capacity is low. Cutters are dull with rounded edges. Low voltage. Current relay set too low. Cutter Stack is Loose New Sharp Cutters are needed. Check voltage at power supply. Consult factory before making any ad ...

• Grease Every week – 1 to 2 Pumps of Grease (See Lube Schedule pg.7) • Appendix 1 at the end of this manual for oil quantities and oil type. ...

chinery Company, Inc., Nevada City, California 95959. The following warranty applies to all Triminator products purchased directly or from retail outlets after January 1, 2013. LENGTH OF WARRANTY All Triminator products are covered under this warranty for a length of 24 months from the date of original purchase. TO QUALIFY FOR THI ...

The following items and conditions are excluded from warranty coverage: 1. Any damage or deterioration resulting from the following: • Neglect of the periodic maintenance as specified in this manual. • Improper repair or maintenance. • The use of non-genuine Triminator parts and/or products other than those approved by Mosman Machinery Company, Inc. • Exposure of the product to chemical agents, sea water, sea br ...