Serato Reloop Terminal Mix 8 Quick Start Manual

The Reloop Terminal Mix 8 is a class compliant USB plug and play device for Mac, however requires drivers for Windows. You will find these on the installation cd provided within your Reloop Terminal Mix 8. NOTE: Please ensure you have the latest available drivers AND firmware updates, which may be required in order to be compatible with Serato DJ. Please go to http://serato.com/dj/support 1. Download and install the latest version of Serato DJ from http://serato. com/dj/downloads 2. After installing drivers, connect your Reloop Terminal Mix 8 to an available USB Port. 3. Open Serato DJ. Serato DJ Activation To find out how to activate Serato DJ by either starting your free 14 day trial, or purchasing a license for Serato DJ, click here for the most up to date information. # Reloop Terminal Mix 8 Comtrol 1 MIC INPUT 2 MIC/AUX LEVEL 3 MIC/AUX TONE 4 INPUT ROUTING MIC 5 INPUT ROUTING PHONO/LINE 6 LEVEL 7 CROSSFADER ASSIGN CHANNEL 3 8 CROSSFADER ASSIGN CHANNEL 1 9 CROSSFADER CURVE 10 CROSSFADER SELECT CHANNEL 2 11 CROSSFADER SELECT CHANNEL 4 12 CUE TONE 13 HEAPHONE INPUT 14 DC IN 15 POWER BUTTON 16 USB 17 MASTER BALANCED OUTPUT 18 MASTER UNBALANCED 19 BOOTH RCA 20 LED DIMMER 21 LED CHAIN 22 AUX INPUT SELECT 23 AUX INPUT 24 GROUNDING POST 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

29 30 31 32 33 34 35 36 37 38 39

Control Function Shift Function 1 DECK FX ASSIGN Assigns FX to selected Deck SHIFT+RANGE will change the available pitch range. SHIFT+KEY will turn on Keylock for selected deck 2 PERFORMANCE PADS See performance pad section for more information 3 FX 1-3 KNOBS/BUTTONS Slots 1-3 Effect On/Off- See DJ-FX section for more information Select FX 4 ON/TAP Enables Autoloop TAP tempo 5 LOOP SIZE/BEATS Auto Loop On/Off or Exit Manual Loop (Click Knob) Auto Loop Length (Twist Knob) Adjust Beats Multiplier 6 EQs Adjust Low/Mid/High 7 GAIN Adjust individual channel gain 8 FILTER LP/HP filter combo adjust 9 CUE MIX Adjusts between Cue and Master in your headphones 10 BOOTH Adjusts booth output volume 11 MASTER Adjusts master output volume 12 PHONES Adjusts headphone output volume 13 SAMPLER VOL Adjusts the master volume of the sample player 14 SLICE Activate Slicer Performance Mode - See performance pad section for more information 15 SMPL Activate Sampler Performance Mode - See performance pad section for more information 16 CUE Activate Hot Cue Performance Mode - See performance pad section for more information 17 LOOP Activate Loop Performance Mode 18 JOG Toggle between Scratch or Jog modes Activates Slip mode NOTE: The SHIFT button is used with other buttons that have shift modifier functions.

Control Function Shift Function 20 LOAD Load track to selected deck Activate Fader Start for that channel 21 POWER Shows unit is being powered by AC 22 DECK 4 Select Active Deck 2/4 (Right Deck) 23 HEAPHONE CUE Cue selected channel in headphones 24 PREPARE Sends highlighted track in library to the PREPARE Crate 25 CROSSFADER Crossfades audio between active decks 26 LED METER LED representation of Master Output 27 BACK Toggles between the Crate list and Library 28 CHANNEL FADERS Adjust channel volume 29 DECK 3 Select Active Deck 1/3 30 PLAY/PAUSE Play/Pause 31 CUE Play from temporary cue point 32 STUTTER Stutter Play 33 SYNC Sync On Sync Off (Press twice to return to Absolute Pitch when in Relative Mode) 34 SHIFT The SHIFT button is used with other buttons that have shift modifier functions. 35 MIDI Shows when MIDI signals are being sent/recieved 36 PLATTER Scratch or Jog deck 37 BROWSE Scroll through tracks and crates. Push to toggle focus between crate list and library. 38 AREA Toggles through FILES, BROWSE, PREPARE and HISTORY panels. 39 TEMPO SLIDER Adjusts Tempo When in Sync mode, used to disable the Pitch Fader temporarily and change the zero position NOTE: #20 LOAD When used with SHIFT, activates Fader Start for each deck. This means the track will stop when the channel fader is down, and the track will start when the channel fader is up. The LOADbutton will flash when Fader Start is activated.

are; SLICE, SMPL, CUE and LOOP. • SLICE Mode: A specified Slicer range (or domain) is divided into eight equal sections, and these eight sliced sections are assigned to the respective performance pads. Pressing SLICE once for the first mode, is a shifting Slicer Domain. Pressing SLICE twice, for the second mode is a fixed Slicer Domain or “slicer loop”. • SMPL Mode: Pads 1-6 Trigger Samples loaded in your Sample Banks. Press and hold SMPL for 1 second or more to activate Sampler Velocity mode. Triggering the pads will play the loaded samples acording to the velocity to which the pads are struck. Holding SHIFT while pressing a pad will load the highlighted track in the library to that associated sample slot. • CUE Mode: When pressing pads 1-8 you can add up to 8 Cue Points. Holding SHIFT and pressing pads 1-8 will delete the Cue Points. • LOOP Mode: Pressing LOOP once for the first mode, is Manual Looping. Pressing LOOP twice for the second mode enables Loop Roll Mode. Pressing pads 1-8 will enable a loop roll for the time the pad is pressed, the loop will exit once the pad is released. See the looping table for more infomation. The SMPL, CUE and LOOP modes are able to be activated together in Dual Mode. You can enable Dual Mode, by pressing two of these Performance Mode buttons at the same time. This splits the 8 performance pads into two lots of 4, allowing you to control two modes on the 8 pads. For example: If you press CUE + LOOP Performance Mode buttons together, the top 4 performance pads will act as Hot Cues, and the bottom 4 pads will act as the first 4 Loop slots. This allows you the versitility of having two performance modes active at the same time.

either manual or auto loops. You can choose whether you have 4 loops (and 4 cuepoints) showing on screen, or 8 loops. To switch between Manual and Auto looping, click (Manual) or (Auto) onscreen. You can also half or double the loop length in either manual or auto modes. Press the 1/2X button onscreen to half the loop length, hold the 2X button to double the loop length, or you can use the Loop Size knob on the controller to do the same. Pad 7 Turn selected Loop on and off 8 Bar Loop Roll Pad 8 Select next loop slot 16 Bar Loop Roll NOTE: The best way to edit the in and out points of a manual loop is with the jog wheel/platter on your Reloop Terminal Mix 4. NOTE: You can also save a loop to the next available free loop slot in the software. To do this, either click the button in the manual/auto loop tab or click on an available loop slot. Your loops are saved to the file and recalled the next time it is loaded. They are not lost if the file is moved or renamed. Reloop Terminal Mix 8 Control Auto Loop Mode ON/TAP Turns Auto Loop ON/OFF LOOP SIZE/BEATS Adjusts Loop length NOTE: Manual Loop and Loop Roll options are done using the Performance Pads. Reloop Terminal Mix 8 Control Manual Loop Mode Loop Roll Mode Pad 1 Trigger Loop/Reloop 1/8 Bar Loop Roll Pad 2 N/A 1/4 Bar Loop Roll Pad 3 Duplicate selected Loop to next slot 1/2 Bar Loop Roll Pad 4 Select previous loop slot 1 Bar Loop Roll Pad 5 Set loop out point (If loop in point is set), Adjust loop out point (Loop active) 2 Bar Loop Roll Pad 6 Set loop in point (Loop not active), Adjust loop in point (Loop active) 4 Bar Loop Roll

playback and mix video files, use effects and fader transitions with your Serato DJ hardware, an additional MIDI controller or your mouse/keyboard. For more information on Serato Video go to http://serato.com/video MIDI The MIDI control feature in Serato DJ provides the ability to map Serato DJ software functions to MIDI controller functions such as keyboards, triggers, sliders, and knobs. Integrating MIDI controllers into your Serato DJ setup can improve live performance usability, such as hitting pads on a MIDI controller to trigger Loops and Cue Points. For more information download the Serato DJ manual by going to http://serato. com/dj/downloads NOTE: You can not MIDI Map your Reloop Terminal Mix 4, you will need to connect an additional MIDI controller to use these MIDI functions. DJ-FX The DJ-FX in Serato DJ are powered by iZotope™. Click the FX tab Screen_ to open the FX panel. Select either 1, 2, 3, 4 or M to assign the selected effect bank to a deck or Master Output. To activate an effect, click the ON button on your FX UNIT in the software, or the FX1 ON button on your controller. You can adjust effect parameters by using either software controls, or the FX1/FX2/FX3 knobs/buttons on the controller. There are two available modes in the DJ-FX. Single FX Mode allows you to se- lect one effect per FX bank, and has multiple parameters that can be adjusted. Multi FX Mode allows you to select up to three effects per FX bank, and adjust only one parameter, the FX Depth. The same effects available in Single FX mode are available in Multi FX mode, as well some additional presets. You can select between the two FX modes by clicking either the Single FX mode button or Multi FX mode button Reloop Terminal Mix 8 Control Manual Loop Mode Loop Roll Mode FX1 Button Effect On/Off Slot 1 Effect On/Off FX1 Knob Adjust FX Slot Parameter (Wet/Dry) Adjusts Slot 1 FX Parameter FX2 Button Adjusts FX Modifier Slot 2 Effect On/Off FX2 Knob Adjusts FX Modifier Adjusts Slot 2 FX Parameter FX3 Button Adjusts FX Modifier Slot 3 Effect On/Off FX3 Knob Adjusts FX Modifier Adjusts Slot 3 FX Parameter SHIFT + FX 1-3 Buttons Select Effect Select Effect in Slots 1-3 NOTE: Use 1 - 2 on the left deck to assign FX UNIT 1 to the Active Deck. Use 1 - 2 on the right deck to assign FX UNIT 2 to the Active Deck.

Click on the icon to enable Tool Tips. This is located in between the MIDI and setup button in the top right hand corner of the screen. Tool Tips provide a handy way to learn the various features of Serato DJ. Move the mouse over a section of the screen to bring up a context sensitive tool tip. Holding the mouse over the button with Tool Tips turned on will show you a list of all keyboard shortcuts. For more information about how to use Serato DJ, please go to our website www.serato.com or refer to the Serato DJ Software Manual. For more information on your controller, please refer to the hardware manual. For further help, please contact [email protected] or go to www.serato.com/ dj/support