Senix GTS4QL-M2 Operator's Manual

Gasoline Powered Trimmer Operator’s manual Model: GTS4QL-M2 For customer support, please call 1-800-261-3981 or send email to: [email protected] SAVE THIS MANUAL FOR FUTURE REFERENCE. ...

SAFETY..........................................................................................2 KNOW YOUR UNIT........................................................................5 SPECIFICATIONS* ........................................................................5 ASSEMBLY......................................................................................6 OIL AND FUEL................................................................................8 STARTING AND STOPPING...........................................................9 OPERATION................................................................ ...

power equipment this unit must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this unit unless they are thoroughly responsible and have read, and understood the string trimmer manual and are trained in its operation. 2. Always wear safety goggles for eye protection. Dress properly. Do not wear loose clothing or jewelry that could become caught in moving parts of the unit. Safe, sturdy, nonskid footwear should always be worn. Secure hair so it is above shoulder level. It is recommended that legs and feet ...

lever immediately. 39. Be careful not to drop the unit or hit it against obstacles. 40. Before proceeding to adjust or repair the unit, be sure to stop the engine and detach the spark plug. 41. When the machine is placed in storage for a long time, drain fuel/oil from the fuel/oil tank and carburetor, clean the parts, and move the machine to a safe place. 42. Make periodic inspections to ensure safe and efficient operation. For a thorough inspection of your unit, contact customer support. 43. Keep the unit away from fire or sparks. 44. Keep your body warm, especially the h ...

• Cutting grass and light weeds • Edging • Decorative trimming around trees, fences, etc. Other optional attachments may be used with this unit. Engine type.................................................................................................................................... Air-Cooled, 4-Cycle Displacement........................................................................................................................................1.9 cu in. (31 cc) Spark plug gap ..........................................................................................................0.025 in. - 0.31 in ...

2. Insert the tab on the mount bracket into the slot in the cutting head shield (Fig. 1). 3. Rotate the cutting head shield until the hole on the mount bracket aligns with the screw hole on the cutting head shield. 4. Insert the screw and tighten until the cutting head shield is firmly in place. The handle can be adjusted for location on the shaft and for angle of grip. To adjust handle: 1. Flip the lever down and turn the nut counterclockwise to loosen the handle (Fig. 2). 2. Hold the unit in the operating position. Move the handle up or down the shaft housi ...

opening. 2. Set the unit on a flat, level surface. 3. Turn the knob counterclockwise to loosen the coupler (Fig. 3). 4. Align the release button with the guide recess (Fig. 4). 5. Push the attachment straight into the coupler until the release button snaps firmly into the primary hole (Fig. 5). 6. Turn the knob clockwise to tighten the coupler. 1. Set the unit on a flat, level surface. 2. Turn the knob counterclockwise to loosen the coupler (Fig. 3). 3. Press and hold the release button (Fig. 4). 4. Pull the attachment straight out of the coupler (Fig. 5). Before op ...

Attempting to start the engine before it has been properly filled with lubricant will result in equipment failure not covered by the warranty. Do not overfill. Overfilling the crankcase may cause excessive smoke, oil loss, and engine damage. OVERFILLING THE CRANKCASE MAY CAUSE SERIOUS PERSONAL INJURY. Check the oil level before each use. The importance of maintaining the proper oil level cannot be overemphasized. Change the oil according to the Maintenance Schedule. Gasoline is extremely flammable. Ignited vapors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while f ...

Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. Operate this unit only in a well-ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. Avoid accidentally starting the unit. To avoid serious injury, the operator and the unit must be in a stable position when pulling the starter rope (Fig. 10). Do not operate the unit inside a closed environment, such as a room or building; breathing carbon monoxide from exhaust fumes can kill. Inspect unit before each use. Replace damaged pa ...

before increasing cutting speed. 7. To increase trimmer cutting speed, press and hold the throttle lockout with one hand, and then squeeze the throttle control with the other. The further you squeeze the throttle control, the more the cutting speed will increase (Fig. 7). NOTE: The lockout will remain engaged as long as the throttle control is being squeezed. NOTE: To prevent the throttle control from being squeezed accidentally, this unit has a throttle lockout. The throttle control cannot be squeezed unless the throttle lockout is also engaged. IF... the ...

straight. Do not bend over. • Keep feet apart and firmly planted. • Hold the shaft grip with the right hand. Keep the right arm slightly bent. • Hold the handle with the left hand. Keep the left arm straight. • Hold the unit at waist level. • Position the cutting head a few inches above the ground. • Do not over-reach; Keep all parts of your body away from the rotating cutting attachment and hot surfaces. • To direct clippings away from you, whenever possible swing the trimmer in a left to right cutting motion. There is an embossed arrow on the top of the safety ...

Excessive line length will make the unit overheat. This may lead to serious personal injury or damage to the unit. • To direct clippings away from the operator, tilt the cutting head slightly down to the right; whenever possible swing the trimmer in a left to right cutting motion. There is an embossed arrow on the top of the safety guard indicating the preferred left to right direction of trimmer operation. • Do not trim wet grass or weeds. NOTE: Some line breakage will occur from: • Entanglement with foreign matter • Normal line fatigue • Attempting to cut thick ve ...

pull to remove (Fig. 14). 2. Install the spring, washer, and rewound spool, making sure that the lines are captured in the holding slots on the new spool. NOTE: Make sure that the ends of the lines extend approximately 6 in. (152 mm). 3. Install the new spool so that the line ends align with the eyelets in the cutting head, and thread the line ends through the eyelets. 4. Pull the lines extending from the cutting head so that the strings release from the slots in the spool. 5. Install the spool retainer by pressing the tabs into the slots and pushing down on the spool until ...

line and thread it through the trimmer head (Fig. 17). NOTE: To avoid vibration, make sure that equal lengths of line protrude through each side of the trimmer head. NOTE: Several 16.25 in. lengths of black 0.130 in. (3.3 mm) spiral Line are supplied with this trimmer. This line is designed for cutting larger weeds and light brush. Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up. NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these p ...

MAINTAINING THE AIR FILTER Old engine oil is considered special waste and has to be disposed according to your local environment protection regulation. Do not pour the oil into a garbage can, sewer, soil etc. DO NOT overfill the oil level. Overfilling will result in too much oil in the engine crankcase, and may cause smoke or fumes that can injure the user. WARNING: WARNING: Change the oil while the engine is still warm. The oil will flow freely and carry away more impurities. 1. Clean the area around the oil fill plug (Fig. 20) to prevent debris from entering the oil fill hole. 2. Unscrew the oil fill plug. 3. Ti ...

1. Start the engine. Refer to Starting and Stopping. 2. Release the throttle control and let the engine idle. • If the engine stops, increase the idle speed. Use a small Phillips screwdriver to turn the idle speed screw clockwise, 1/8 of a turn at a time, until the engine idles smoothly (Fig. 24). • If the cutting head spins when the engine idles, reduce the idle speed. Turn the idle speed screw counterclockwise, 1/8 of a turn at a time, until the cutting head stops moving (Fig. 24). 1. Stop the engine and allow it to cool. Grasp the spark plug boot firmly and pull it from the spark plug ...

open flame or spark. • Allow the engine to cool before storing. • Lock up the unit to prevent unauthorized use or damage. • Store the unit in a dry, well-ventilated area. • Store the unit out of the reach of children. Short-term Storage (1-2 weeks) Store the unit in a horizontal position. If not possible, store the unit vertically with the engine at the top. Long-term Storage 1. Remove the fuel cap, tip the unit and drain the fuel into an approved container. Reinstall the fuel cap. 2. Start the engine and allow it to run until it stalls. This ensures that all fuel has ...

The fuel tank is empty Fill the fuel tank with fresh fuel The primer bulb was not pressed enough Press the primer bulb 10 times The fuel is old (over 30 days) Drain the fuel tank and add fresh fuel The spark plug is fouled Replace the spark plug THE ENGINE WILL NOT IDLE The air filter is dirty Clean or replace the air filter The fuel is old (over 30 days) Drain the fuel tank and add fresh fuel THE ENGINE WILL NOT ACCELERATE The fuel is old (over 30 days) Drain the fuel tank and add fresh fuel The cutting head is bound with grass Stop the engine and clean the cutting head The air filter is ...

No. Part # Description Qty. 1 103001000297 Engine head 1 2 201999001337 Tube fixed circle 1 3 207310100743 Screw 1 4 207320100013 Hexagon nut 2 5 199999001314 - 1 6 199004000604 Handle assembly 1 6-1 207310100263 Screw 6 6-2 202024002102 Hand shank 1 6-3 199081000107 Cable assembly 1 6-4 199999001152 Stopping wire 1 6-5 207180200023 Switch 1 6-6 202024002101 Hand shank 1 6-7 202042000207 Driving lever 1 6-8 202004000897 Trigger 1 6-9 303000003 Wire cover 1 6-10 207019900345 Return spring 1 6-11 202999001491 Control circle 1 7 201024000009 Harness ring 1 8 208008000051 Har ...

Additional Limitations 3-year limited warranty on all Senix 4QL series gasoline powered equipment. FOR THREE YEARS from the original date of retail purchase this Senix product is warranted against defects in materials or workmanship on power tools. Defective product will receive free repair.* This warranty does not cover normal wear of parts and components such as cutting chain, line or blades nor does this warranty cover product transportation cost for warranty or service. Any implied warranty granted under state law, including warranties of merchantability or fitness for a particular purpose, ...