Senix CSP4QL-L Operator's Manual

Engine Gasoline Powered Pole Saw Operator’s manual Model: CSP4QL-L For customer support, please call 1-800-261-3981 or send email to: [email protected] SAVE THIS MANUAL FOR FUTURE REFERENCE. ...

This operator’s manual describes safety and international symbols and pictographs that may appear on this product. Read the operator’s manual for complete safety, assembly, operating and maintenance and repair information. To reduce the risk of injury, user must read instruction manual. Contact of the guide bar tip with any object should be avoided. Tip contact can cause the guide bar to to move suddenly upward and backward, which can cause serious injury. Always use two hands when voperating the pole saw. DO NOT USE E85 FUEL IN THIS UNIT CAUTION: It has been proven that fuel containing gr ...

SAFETY..........................................................................................3 KNOW YOUR UNIT........................................................................7 SPECIFICATIONS*.........................................................................7 ASSEMBLY......................................................................................8 OPERATION..................................................................................11 MAINTENANCE............................................................................14 TROUBLESHOOTING.................................................. ...

worn. • Damage to hearing if effective hearing protection is not worn. • Health defects resulting from vibration emission if the unit is being used over long periods of time or not adequately managed and properly maintained. Even when the unit is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the unit’s construction and design: WARNING: 13. Never start or run the product inside a closed room or building. Fumes from the exhaust contain dangerous carbon monoxide. 14. Never atte ...

PRUNERS ADDITIONAL SAFETY WARNINGS FOR OPERATION 1. Wear head and eye protection and personal protective equipment (PPE), including correct clothing. 2. Keep bystanders, especially children at a safe distance during operation of the saw chain pole pruner. 3. Keep all parts of the body away from the saw chain. Do not remove cut material or hold material to be cut when blades are moving. Make sure the switch is off when clearing jammed material. The saw chain continues to move after the switch is turned off. A moment of inattention while operating the extended- reach pruner may result in serious persona ...

WARNING: WARNING: The danger of a kickback is greatest when attempting to cut near or with the guide bar tip. Always apply the saw as flatly as possible in order avoid a loss of control during operation. When removing branches, hold the pole saw at an angle ranging from 0 to 60° in order to avoid being struck by a falling branch. The saw should never be operated directly above head. Pinching the saw chain along the top of the guide bar can push the bar rapidly towards the operator. Either of these reactions may cause a loss in control of the saw, increasing the chances of serious personal injury. Do not rel ...

• Cutting small limbs • General tree pruning Engine type......................................................................................................................................Air-Cooled, 4-Cycle Displacement...................................................................................................................................1.62 cu in. (26.5 cc) Spark plug gap...........................................................................................................0.025 in. - 0.31 in. (0.6 - 0.8 mm) Lubrication........................................................................... ...

POWER HEAD SHAFT/LOWER SHAFT ASSEMBLY ASSEMBLY INCLUDED PARTS This product requires assembly. Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included. Inspect the product carefully to make sure no breakage or damage occurred during shipping. Do not discard the packing material until you have carefully inspected and satisfactorily operated the product. If any parts are damaged or missing, please call 1-800-261-3981 for assistance. Do not use this product if any parts on the packing list are already assembled to your product when you ...

Disconnect the spark plug wire before performing maintenance or assembly procedures. Cutting edges on chain are sharp. Use protective gloves when handling chain. ALWAYS maintain proper chain tension. A loose chain will increase the risk of kickback. A loose chain may jump out of chain bar groove. This may injure operator and damage chain. A loose chain will cause chain, chain bar, and sprocket to wear rapidly. The chain life of the saw chain mainly depends upon sufficient lubrication and correct tensioning. Avoid tensioning the chain if it is hot, as this will cause the chain to become over tensioned ...

FILLING THE OIL TANK ADDING/CHECKING ENGINE OIL ADD ENGINE OIL: INITIAL USE CHECK ENGINE OIL: BEFORE EACH USE The pole saw features automatic chain lubrication. Never operate the pole saw without saw chain oil. The use of the pole saw without enough saw chain oil will damage the unit. Only use SAE300 saw chain oil. Other oils will run the risk of damaging the unit and voiding the warranty. Take note of temperature conditions. Using the saw at various temperatures requires the use of differing oils. To ensure a sufficient layer of lubricant at lower temperatures, use liquid oil (low viscosity). 7. If adjustmen ...

recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury. Gasoline is extremely flammable. Ignited vapors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the area. Remove the fuel cap slowly to avoid injury from fuel spray. Never operate the unit without the fuel cap securely in place. Add fuel in a clean, well-ventilated outdoor area. Wipe up any spilled fuel immediately. ...

use of the unit on the operator’s left side will expose the user to hot surfaces and can result in possible burn injury. To avoid burns from hot surfaces, never operate unit with the bottom of the engine above waist level. Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with hearing protection. Failure to do so could result in objects being thrown into your eyes and other possible se ...

not bend over. • Keep feet apart and firmly planted. • Hold the shaft grip with the right hand. Keep the right arm slightly bent. • Hold the handle with the left hand. Keep the left arm straight. • Hold the unit at waist level. • Position the cutting head a few inches above the ground. • Do not over-reach; Keep all parts of your body away from the rotating cutting attachment and hot surfaces. STARTING AND STOPPING Restart a warm engine: HOLDING THE UNIT STOP THE ENGINE: To start a cold engine: 1. Slowly press the primer bulb 5-10 times. NOTE: After the 7t ...

and allow it to cool before cleaning or maintaining the unit. Never perform cleaning or maintenance while the unit is running. Disconnect the spark plug wire to prevent the unit from starting accidentally. Wear protective clothing and observe all safety instructions to prevent serious personal injury. Old engine oil is considered special waste and has to be disposed according to your local environment protection regulation. Do not pour the oil into a garbage can, sewer, soil etc. The air filter element should be cleaned to provide the engine abundant clear air wh ...

the idle speed screw counterclockwise to reduce the idle RPM and stop the cutting attachment, or contact customer support for adjustment and discontinue use until the repair is made. Serious personal injury could result from the cutting attachment turning at idle. To avoid serious personal injury, always stop the engine and allow it to cool before cleaning or maintaining the unit. Never perform cleaning or maintenance while the unit is running. Disconnect the spark plug wire to prevent the unit from starting accidentally. Replace chain when cutters are too worn to sharpen or w ...

personal injury. Transport the unit in a horizontal position. If not possible, transport the unit vertically with the engine at the top. Secure the pole saw to prevent damage during transport. CAUTION: TRANSPORTATION NOTE: Do not use fuel that has been stored for more than 30 days. Dispose of old fuel and oil according to federal, state and local regulations. ...

TROUBLESHOOTING PROBLEM SOLUTION THE ENGINE WILL NOT START The fuel tank is empty Fill the fuel tank with fresh fuel The primer bulb was not pressed enough Press the primer bulb 10 times The fuel is old (over 30 days) Drain the fuel tank and add fresh fuel The spark plug is fouled Replace the spark plug THE ENGINE WILL NOT IDLE The air filter is dirty Clean or replace the air filter The fuel is old (over 30 days) Drain the fuel tank and add fresh fuel Idle speed screw needs adjustment Turn idle speed screw clockwise to increase idle speed THE ENGINE EM ...

1 4 199141000002 Pole saw head assembly 1 5 8SJJD05-25D Screw 1 6 199999001469 Lower Drive Shaft assembly 1 7 199999001468 Extension Tube assembly 1 8 199999001470 Rear tube assembly 1 9 8SJJD05-10D Screw 3 10 103001000301 26.5 cc engine 1 11 199004000574 The handle assembly 1 11-1 8SJEB40-14D Screw 5 11-2 202024002294 Right handle 1 11-3 8342-902101-0000000 Return spring 1 11-4 202999001676 Control circle 1 11-5 202004000882 Throttle trigger 1 11-6 202042000206 Control lever 1 11-7 202024002295 Le ...

Additional Limitations 3-year limited warranty on all Senix 4QL series gasoline powered equipment. FOR THREE YEARS from the original date of retail purchase this Senix product is warranted against defects in materials or workmanship on power tools. Defective product will receive free repair.* This warranty does not cover normal wear of parts and components such as cutting chain, line or blades nor does this warranty cover product transportation cost for warranty or service. Any implied warranty granted under state law, including warranties of merchantability or fitness for a particular purpose, ...