WATSON Bahn Assembly Instructions Manual
Text of WATSON Bahn Assembly Instructions Manual
2 Bahn Rail Assembly | INS-BNRAIL
RAIL TYPICAL
FASTENERS
TOOL TIPS
Mid Leg
End Screen
End Leg
Spine Screen
¼-20x1” Phillips Pan
Head Machine Screw
(119000)
5/32 Hex Key
3/16 Hex Key
FF2 Phillips
5/16-18x4” Button
Head Socket Cap
Screw (0000631)
¼-20x⅜” Button
Head Socket Cap
Screw (123547)
#10-32x⅜” Phillips
Pan Head Thread
Rolling Screw (121376)
Rail
1/4-20x13/4”
Connector Bolt
(0000613)
¼-20x⅜” Button
Head Socket Cap
Screw (
3 Bahn Rail Assembly | INS-BNRAIL
RAIL COMPONENTS
Rail
Mid Leg
Single-Sided
Aisle End Screen
Raceway Spine Screen
Infeed
Cable Clip
Jumper
End Leg
Dual-Sided
Aisle End Screen
Riser
End Cover
Dual-Sided
Aisle End Screen
Single-Sided
Aisle End Screen
Modesty Tray
Modesty Panel
4 Bahn Rail Assembly | INS-BNRAIL
Rail Supports
A End Leg: Attach the end leg to the
underside of the rail with 1/4-20x3/8” screws (x4)
(123545)
B Mid Leg: Attach the mid leg to the
underside of the rail with 1/4-20x3/8” screws (x8)
(123545)
C End Screen (Optional): Attach end screen
bracket to underside of rail with ¼-20x3/8”
screws (x4) and 1/4-20x1” screws (x2)
(123545)
(119000)
Level and Adjust Tilt
A Leveling: With a 7mm Hex Key,
5 Bahn Rail Assembly | INS-BNRAIL
Jumpers
Feed jumper through the rail channel and
above the mid leg support bracket. Refer
to the chart for appropriate length.
Mid Run Infeed Connection
Route the infeed through the cutout
in the underside of the rail. Route the
connection to either junction box in the
rail.
IMPORTANT
Note — Connections are keyed to snap in
one way with a positive click. Do not modify
the jumper or harness block as this creat
6 Bahn Rail Assembly | INS-BNRAIL
End of Run Infeed Connection
Floor or Wall Connection: Route the infeed through
through the cutout in the bottom of the rail.
Duplexes
A Connect the power infeed and jumpers
to the duplexes. Make sure the connection
is fully inserted. This will be indicated by
an audible click.
B Install duplexes using #10-32x⅜”
Phillips Pan Head Thread Rolling Screw
(x2 per duplex)
(121376)
6.
5.
A
B
7 Bahn Rail Assembly | INS-BNRAIL
End Cover
Attach the end cover to any end-of-run
rail segments with #10-32x3/8” screws
(x4 ea). The cover geometry will
depend on whether a modesty screen
was ordered or not.
(121376)
Spine Screens (Optional)
With the assistance of another person
to stabilize the screen, attach the spine
screens to the rail with 5/16-18x4”
screws (x4 ea) from underneath.
(0000631)
8.
7.
8 Bahn Rail Assembly | INS-BNRAIL
Modesty Screen (Optional)
A Connect the modesty brackets to
the underside of the rail with 1/4-20x3/8”
screws (x4 ea).
(123545)
B Attach the modesty tray to the
brackets using 1/4-20x3/8” screws (x4 ea).
(123545)
C Insert wire management clips into the
holes in the modesty tray.
(0000003)
Modesty Screen (Optional)
Attach the modesty panels to the modesty
brackets by hooking the panel clips onto
brackets and
9 Bahn Rail Assembly | INS-BNRAIL
WIRING SCHEMATIC
120 / 240V 1 ph
FOR 2+2 USE CIRCUITS 1, 3 , 4 ONLY
FOR 3+1 USE CIRCUITS 1, 3, 4 ONLY
CIRCUIT 2 CAN NOT BE UTILIZED
WITH 120/240V
120 / 208V 3 ph
FOR 2+2 USE CIRCUITS 1, 2, 3 , 4 ONLY
FOR 3+1 USE CIRCUITS 1, 2, 3, 4 ONLY
MAX 20AMPS PER CIRCUIT
MAXIMUM SEGMENTS CONNECTED:
12 STANDARD POWER
6 HEAVY POWER
MAX 20AMPS PER CIRCUIT
MAXIMUM SEGMENTS CONNECTED:
12 STANDARD POWER
6 HEAVY POWER
BLACK
WHIT
26246 Twelve Trees Lane NW, Poulsbo, Washington 98370
360.394.1300 watsonfurniture.com [email protected]
Notes