Warn 93730 Installation Instructions Manual

1 93731A0 WARN INDUSTRIES, INC. 12900 S.E. Capps Road, Clackamas, OR USA 97015-8903, 1-503-722-1200, FAX: 1-503-722-3000 Customer Service: 1-800-543-9276 Dealer Locator Service: 1-800-910-1122 International Sales/Customer Service: 1-503-722-3008 International Fax: 1-503-722-3005 INSTALLATION INSTRUCTIONS PLOW MOUNT KIT Part Number: 93730 Application: 2015+ Honda Pioneer 500 G E N E R A L S A F E T Y P R E C A U T I O N S W A R N I N G IMPACT AND MOVING PARTS ENTANGLEMENT HAZARD Failure to observe these instructions could lead to severe injury or death • Alw ...

2 93731A0 N O T I C E EQUIPMENT DAMAGE • Always refer to the Installation and Specification Guide, supplied in the winch kit, for all wiring schematics and specific details on how to wire this WARN product to your vehicle. Read installation and operating instructions thoroughly. C A U T I O N MOVING PARTS ENTANGLEMENT HAZARD Failure to observe these instructions could lead to minor or moderate injury • Always take time to fully read and understand the installation and Operations Guide included with this product. • Never operate this product if you are und ...

3 93731A0 P A R T S L I S T Item Part Number Qty Description A 93735 1 Plow Mount Bracket B 89079 2 U-bracket C 93739 2 V-bracket D 79341 1 Left Hand Flange E 79340 1 Right Hand Flange F 93729 2 Sleeve G 93100 4 M8 Nut H 92834 4 M6 Socket Screw J 92013 4 M8 Carriage Bolt K 35136 2 Pin L 6 M10 Bolt (supplied with plow push tube kit) M 6 M10 Nut (supplied with plow push tube kit) N 2 M10 Bolt (re-use factory bolt) T O O L S R E Q U I R E D - 8, 10, 12, 13, 14, 15mm sockets - 8, 10, 12, 13, 14, 15mm wrenches - 5mm hex wrench - Ratchet Wrench - Mallet/hammer and w ...

4 93731A0 I N S T A L L A T I O N I N S T R U C T I O N S 1. Using a mallet, flatten slightly (about 1/8 inch) the last 4 inches of each tube. 2. Install sleeves into plow push tubes, flattened section last. Drive sleeve down until flush. ...

5 93731A0 3. Install plow mount bracket to vehicle using factory front guard bolts, V-brackets, U-brackets and M8 carriage bolts. See parts list diagram. V-bracket installs between frame and plow mount bracket, with the notched end down. Do not tighten fasteners yet. 4. Install RH & LH flanges to plow push tubes. Do not tighten fasteners yet. 5. Re-install winch, if required. Reconnect vehicle battery. 6. Install plow to vehicle mount. See Push Tube kit instructions for more information. 7. With the vehicle on level ground, use the winch to lift the blade up ...

6 93731A0 CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS PRODUCT. M A I N T E N A N C E / C A R E 1. Inspect all parts on the winch, winch mount, and related hardware prior to each use. Replace all hardware that appears rusted or deformed. 2. Inspect all nuts and bolts on the winch, winch mount,, and related hardware prior to each use. Tighten all nuts that appear to be loose. Stripped, fractured, or bent bolts o ...