Seco VINCO 600 Manual 

VINCO 600 - 800 - 1000 - 1500 - 2000 - 2500 MANUAL R www.seco.gr Tel. 0030 210 9846222 Fax 0030 210 9822276 Agiou Dimitriou 263, TK. 17342, Athens, Greece ENG GR

THIS SERIES OF DOOR OPENERS MUST BE INSTALLED BY PROFESSIONALS. 1. ATTENTION! Please operate the machine carefully in strict compliance with instructions of this Manual. It is very important to personal safety . Incorrect installation or improper use of the machine may cause serious damage to the person and/or property. 2. Read this Manual carefully before installation. 3. The installation must comply with relevant national codes and specifications and the mechanical parts used must meet with national standards. 4. The power supply should have a voltage meeting the requirements of the machine, be reliably grounded, and have both leakage protection and short circuit protection. 5. Before system overhaul, cut off the power and check if the grounding system is correct and reliable. 6. The machine must be equipped with safety devices (such as infrared intrusion protector) (optional) and should be inspected on a frequent basis for normal operation. 7. We will accept no responsibility for any consequences resulting from inappropriate use of the machine or from use beyond the specified purposes. 8. We will accept no responsibility for any problem incurred due to neglect of the process requirements of precision components or due to deformation of such components during the installation. 9. The product was designed and manufactured in strict compliance with the operating instructions given in this Manual. Any use or operation against these instructions may damage the product or bring a hazard. 10. We will accept no responsibility for any safety problem or operation failure caused by the use of any component not produced by us. 11. Don’t make any change to the components of the system. 12. The installer must explain in detail to the user the operating rules of the machine and relevant regulations in case of an emergency, and provide the user with the Manual. 13. Keep children and other unauthorized persons away from the installation site and make sure there is no risk factor existing in the vicinity of the installation site. 14. Clean off any obstacle from the motion route of the door before the electric control system is put into operation, and stop the flow of vehicles and pedestrians when the door is in motion. 15. The main control box should be installed in such a position and to such a height that should be appropriate, ventilated, and properly protected from rain, sunshine, playing kids, and the operation of remote control and control panel switch by mistake. 16. An external housing may be added if necessary. In doing so, the shielding effect of the external housing (usually made of metal) against the receiving of remote control signals should be taken into account since it may affect the product’s functionality and bring inconvenience to the user. 17. Keep the remote control out of the reach of children. Failure to do so may incur accident to children. 18. Don’t try to repair or adjust the system by yourself. Contact professionals instead. 19. Keep the Manual properly for future use. R VINCO Sliding Gate Opener 2

Working Principle and Main Components and Functions The door opener mainly consists of a high-strength aluminum alloy box, a high-quality single-phase motor, a frictional overrun clutch, a worm-gear reducer, a gear clutch and an output gear. During the operation, the motor spindle drives both the reducer and output gear by means of the frictional overrun clutch, and the output gear then push racks mounted on the sliding door to move the door horizontally so that the door can be opened and closed in the energized state. When the special key is turned clockwise, the gear clutch is engaged and the motor power transmitted by the worm gear drives the output gear to rotate via the gear clutch so as to drive the rack mounted on the door, pushing the door to move (or to open and close) horizontally. Meanwhile because of the reverse self-locking feature of the worm gear mechanism, the door is locked as well, keeping closed against an external force. When the special key is turned counterclockwise, the left and right parts of the gear clutch are disengaged from each other and the output gear is freed from the influence of the motor, allowing the door to be opened and closed manually. Install the Metal Base The door opener should be mounted on a metal base with bolts. As for how to install the metal base, see Fig. 1. MODEL VINCO 600 Supply Voltage(V) Motor Power(W) Torque Maximum Weight Of Gate Motor Rotation Speed(Rated) Gate Speed Limit Switch Noise Operating Environment Temperature Certifcates MODEL Supply Voltage(V) Motor Power(W) Torque Maximum Weight Of Gate Motor Rotation Speed(Rated) Gate Speed Limit Switch Noise Operating Environment Temperature Certifcates AC230/120V 280W 20Nm 600kg 1400r/min 12M/Minute Spring switch/magnetic switch ≤56dB -45oC - 65oC CCC, CE AC230/120V 370W 20Nm 800kg 1400r/min 12M/Minute Spring switch/magnetic switch ≤56dB -45oC - 65oC CCC, CE AC230/120V 550W 20Nm 1000kg 1400r/min 12M/Minute Spring switch/magnetic switch ≤56dB -45oC - 65oC CCC, CE AC230/120V 750W 20Nm 1500kg 1400r/min 12M/Minute Spring switch/magnetic switch ≤56dB -45oC - 65oC CCC, CE AC230/120V 1200W 20Nm 2000kg 1400r/min 12M/Minute Spring switch/magnetic switch ≤56dB -45oC - 65oC CCC, CE AC230/120V 1500W 20Nm 2500kg 1400r/min 12M/Minute Spring switch/magnetic switch ≤56dB -45oC - 65oC CCC, CE VINCO 800 VINCO 1000 VINCO 1500 VINCO 2000 VINCO 2500 3 www.seco.gr Tel. 0030 210 9846222 Fax 0030 210 9822276 Agiou Dimitriou 263, TK. 17342, Athens, Greece

The easiest way to install a rack is to place it on the gear teeth of the door opener first, disengage the door opener, and then push the door slowly to move the tack bit by bit to the desired position. In this way, you can make sure that the teeth of the rack are perfectly engaged with the teeth of the gear. When doing so, don’t forget to mark each mounting point. (See Fig. 2.) Be noted not to lay the entire weight of the door onto the gear. Door Opener Release Device (Open the door manually) The door opener is designed with a lockable release device which enables you to open the door manually in case of blackout. For the release device and its operations, see Fig.3 and Fig. 4. Install the Limit Switch Install the switch bracket onto the rack by reckoning the final travel position. (See Fig. 5). For a spring switch, adjust until to an inclination that the spring comes into contact with the switch flapper. For a magnetic switch, the magnet should point to the motor and be located according to the position of the magnetic limit switch inside the housing. SC - SDCB102 Control Panel for Sliding Gate Motors R 4

For control panel wiring, see Control Panel Manual. Energizing & Trial Run 1. Before use, check the power supply voltage, frequency and other data carefully and make sure they are in line with the requirements, and check if the ground wire is in good condition and the electrical wiring is correct. 2. A special key is provided along with the shipment of the door opener. Turn the key counterclockwise (to disengage the clutch), push the sliding door and let the door opener to operate without load. If the door opener works properly, then turn the key clockwise (to engage the clutch). 3. Turn on the power, start the door opener, and observe the sliding operation of the sliding door. 4. Adjust the magnet’s position until the door is able to open and close in positions to your satisfaction. Care and Maintenance 1. Apply some antirust grease to the end of the worm gear spindle located inside the hole of the special key. 2. Check frequently if the electrical grounding is in good condition. 3. Check frequently if all parts and components are in good condition. 4. The device uses advanced lubricant that requires no replacement or replenishment. www.seco.gr Tel. 0030 210 9846222 Fax 0030 210 9822276 Agiou Dimitriou 263, TK. 17342, Athens, Greece 5