Vaillant timeSWITCH 150 Operating And Installation Instructions

Contents 1 Safety . . . . . . . . . . . . . . . . . . . . . 4 1.1 Information ................................ 4 1.2 Intended use .............................. 4 1.3 General safety information .......... 6 1.3.1 Risk caused by inadequate qualifi- cations ........................................ 6 1.3.2 Danger caused by short-circuits ..................................... ...

Contents 4.6 Summer time mode ................... 12 4.7 Power failure .............................. 13 4.8 Care ........................................... 13 4.9 Recycling and disposal .............. 13 5 Installation . . . . . . . . . . . . . . . . . 14 5.1 Set-up ........................................ 14 5.2 Start-up ...................................... 16 5.3 Handing ...

1 Safety 1 Safety 1.1 Information Observe the information in these instruc- tions. Information is labelled as follows: Note! Useful information and instruc- tions 1.2 Intended use In the event of inappropriate or improper use, damage to the product and other property may arise. The product is a 24-hour timer used to time control Vaillant boiler with or without hot water supply. The pr ...

Safety 1 Intended use also covers installation in accordance with the IP code. This product can be used by children aged from 8 years and above and per- sons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and under- stand the hazards involved. Childr ...

1 Safety 1.3 General safety information 1.3.1 Risk caused by inadequate qualifications The following work must only be carried out by competent persons who are suffi- ciently qualified to do so: – Set-up – Dismantling – Installation – Start-up – Decommissioning • Proceed in accordance with current technology. The competent person must be approved at the time by the “Healt ...

Safety 1; Notes on the documentation 2 particularly the “Safety” section and the warnings. • The end user may carry out the activi- ties for which instructions are provided in the “Operation” section in these instructions. 1.4 Regulations (directives, laws, standards) • The competent person must observe the national regulations, standards, directives, ordinances and laws. 2 ...

2 Notes on the documentation; 3 Product description 2.3 Validity of the instructions These instructions apply only to: timeSWITCH 150 0020116882 3 Product description 3.1 Product design 12 3 6 9 1 5 2 3a 4 3b 1 Minute hand 2 Time mark 3a Slide pushed in (boiler on) 3b Slide pulled out (boiler off) 4 Time of day 5 Operating mode switch ...

Product description 3 3.2 Main functions Minute hand (1) For displaying and setting the time. Time mark (2) The triangular time mark indicates the time of day (e. g. 3.00 pm in Fig. 3.1). Slide pushed in (3a) The boiler is switched on by a pushed in slide and remains on until the timer arrives at a pulled out slide. Slide pulled out (3b) The boiler is switched off by a pulled out slide ...

3 Product description 3.4 CE marking The CE marking shows that the products comply with the basic requirements of the applicable directives as stated on the declaration of conformity. The declaration of conformity can be viewed at the manufacturer’s site. 3.3 Data Plate The data plate is located inside the con- trol on the rear of the timer’s electronics (PCB). Information on the ...

Operation 4 4 Operation This section contains instructions regard- ing activities that the end user may carry out. 4.1 Selecting the operating mode You can use the operating mode switch (5) to change the operating mode of your boiler as desired. – The boiler is switched off permanently if set to “off”. – The boiler is switched on permanently if set to “on”. – The boiler ...

4 Operation 4.3 Setting slides Set the slides as follows: • Push the slides inwards for heating periods (3a). • Pull the slides outwards for periods without heating (3b). 4.4 Setting the heating program • Set the slides as desired and set the operating mode switch (5) to the auto- matic heating program “ ”. 4.5 Weekend mode • Turn the operating mode switch to “on” if t ...

Operation 4 4.7 Power failure The timer cannot be operated with batter- ies. The clock is switched off in the event of a power failure. The set program is retained however. The preset program is resumed once the timer is supplied with power again. Note! After a power failure you must check the time of day and adjust it if necessary (refer to Section 4.2)! 4.8 Care • Clean the time ...

5 Installation 5 Installation This section contains instructions regard- ing activities that only the competent per- son may carry out. 5.1 Set-up The timer is connected to the boiler by pin header connectors on the timer. The timer is pushed directly into the installa- tion recess provided for this purpose, establishing an electrical connection to the boiler in the process. Note! Wh ...

Installation 5 • Carefully press the timer into the con- nection in the electronics box. If there are horizontal plug connections without pins on the electronics box: 2 1 • Insert the short ends of the 4-pin head- er connector (2) included with the timer into the four horizontal openings on the PCB for the timer (1). ...

5 Installation • Carefully press the timer unit with the pin header connector into the connec- tion in the electronics box. 5.2 Start-up • Switch on the power supply for the boil- er. • Put the boiler into service in accord- ance with the operating and installation manual of the boiler. 5.3 Handing over to the owner You must show the owner how to handle the timer and inform the ...

Installation 5 5.4 Decommissioning • Switch off the boiler. • Disconnect the appliance from the power supply. • Carefully remove the timer from the electronics box’s plug-in connection. • Secure the cover plate on the electron- ics box. 5.5 Recycling and disposal • Dispose of the packaging correctly. • Observe all relevant regulations. • Do not dispose of the product w ...

6 Guarantee and customer service 6 Guarantee and customer service 6.1 Guarantee We only grant a Vaillant manufacturers warranty if a suitably qualified engineer has installed the system in accordance with Vaillant instructions. The system owner will be granted a warranty in accordance with the Vaillant terms and conditions. All requests for work during the guarantee period must be mad ...

Technical data 7 7 Technical data Rated voltage 24 V Rated current 35 mA Rated surge voltage 330 V Approx. weight 200 g Protection rating IP 20 Protection class II Pollution degree 2 Temperature for the ball pressure test 75 °C Maximum permitted environ- mental temperature 0 ... 60 °C Current room air hum. 35 ... 95 % Mode of operation Type 1 Height 97 mm Width 146,5 mm Depth 17,5 m ...