Savant PAV-VIM8S series Deployment Manual
Read Online
Read the Savant PAV-VIM8S series Deployment Manual online using the built-in PDF viewer.
Key Pages of Document
45 Perseverance Way, Hyannis, MA 02601 - 1 - Savant.com | 508.683.2500 Document Number: 009-1551-04 Document Date: July 2019 Document Supports: da Vinci 8.8 and higher Savant® IP Video PAV-VIM8S, PAV-VIM4S, PAV-VIMVP1F, PAV-VIMVP1C, PAV-VIM1C PAV-VOMVP1F, PAV-VOMVP1C, PAV-VOM1C Deployment Guide ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 2 of 38 Contents To access the link to the topics in this document, click the topic page. 1. Introduction ............................................................................................................... 4 2. Deployment Steps .................................................................................................. 5 3. IP Video Equ ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 3 of 38 Before installing, configuring, or operating any equipment and other, Savant recommends that each dealer, integrator, installer, etc. access and read all the relevant technical documentation. Savant technical documentation can be located by visiting Savant.com. Vendor documentation is supplied with the equipment. Read and understand all safety inst ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 4 of 38 1. Introduction The Savant IP Video is a scalable UHD (4K) Video Matrix using a Savant verified 10G network switch. This document will guide the installer through the process of installing, configuring, and adding Savant IP Video devices to a RacePoint Blueprint™ configuration. The figure below shows the basic application. The audio path can eith ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 5 of 38 Before You Begin Read through this document in its entirety and ensure that the following required items are available: Savant IP Video Transmitter 4K UHD with Control ................................................................................................................................................................ (PAV-VIM8S, PAV-VIM4S ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 6 of 38 3. IP Video Equipment Overview 3.1. Box Contents and Specifications Refer to the Quick Reference Guide for these products located on the Savant Customer Community for Box Contents and Specifications. 3.2. PAV-VIM8S or PAV-VIM4S Front Panel A B C D E A On / Off Button Reboots the main board (mcu) and power cycles the IP Video transmit (Tx) cards B R ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 7 of 38 Rear Panel L R L R R L R L L R R L L R R L K J I H G F E D C B A A 1 Gigabit Ethernet 1G of reserved network data bandwidth commonly used to connect any network compliant device to transmit its data onto the Ethernet network by sharing the 10G network link. 8-Pin RJ-45 female connection. This is a courtesy port. It will not work for all network fun ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 8 of 38 3.3. PAV-VIMVP1F or PAV-VIMVP1C Front Panel A B C D E F G A RSVD LED Reserved for future use. Blue - LED on by default. B Link TX LED Off - No valid connection. Blue - Valid link. Blinking - Sending Ethernet Data. C Link RX LED Off - No valid connection. Blue - Valid link. Blinking - Receiving Ethernet. D Video LED Off - No video signal detected. B ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 9 of 38 Rear Panel DC 12V HDMI IN OPITCAL OUT RS232 RS232 LAN(C) IR OUT IR IN AUDIO - + 12V TX RX G DP IN B D E F G H A C I J K A Power Input 12V DC. B DP In Display Port: Not used. C HDMI In 19-Pin Type A HDMI female digital audio/video input. Supports HDMI 2.0a. HDMI 2.0 complaint cable required for 4K content. D Optical out or 10 GbE 10G input from t ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 10 of 38 3.4. PAV-VIM1C Top View A B C D E F A Power LED Off - Device is off. No power applied. Blue - Main board is powered. B Video LED Off - No video signal detected. Blue - Video signal detected. C Link TX LED Off - No valid connection. Blue - Valid link. Blinking - Sending Ethernet Data. D Link RX LED Off - No valid connection. Blue - Valid link. Blin ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 11 of 38 Rear Panel I H F E D C B A G J K A DC 12V 12V DC. B HDMI In 19-Pin Type A HDMI female digital audio/video input. Supports HDMI 2.0a. HDMI 2.0 complaint cable required for 4K content. C RS232 4-pin Control Connector. Transmits and receives serial data to and from serial controllable devices. For pin- out information, refer to the RS-232 Wiring sect ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 12 of 38 3.5. PAV-VOMVP1F OR PAV-VOMVP1C Front Panel A B C D E F G A RSVD LED Reserved for future use. Blue - LED on by default. B Link TX LED Off - No valid connection. Blue - Valid link. Blinking - Sending Ethernet Data. C Link RX LED Off - No valid connection. Blue - Valid link. Blinking - Receiving Ethernet. D Video LED Off - No video signal detected. ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 13 of 38 Rear Panel B D E F G H A C I J A Power Input 12V DC. B HDMI OUT 19-Pin Type A HDMI female digital audio/video output. Supports HDMI 2.0a. HDMI 2.0 complaint cable required for 4K content. C Optical out or 10 GbE 10G input from the IP Video network switch. SFP+ (PAV-VIMVP1F) RJ-45 (PAV-VIMVP1C) D RS-232 4-pin Control Connector. Transmits and receiv ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 14 of 38 3.6. PAV-VOM1C Top Panel A B C D E F A Power LED Off - Device is off. No power applied. Blue - Main board is powered. B Video LED Off - No video signal detected. Blue - Video signal detected. C Link TX LED Off - No valid connection. Blue - Valid link. Blinking - Sending Ethernet Data. D Link RX LED Off - No valid connection. Blue - Valid link. Bli ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 15 of 38 Rear Panel I H F E D C B A G J K A DC 12V 12V DC. B HDMI Out 19-Pin Type A HDMI female digital audio/video output. Supports HDMI 2.0a. HDMI 2.0 complaint cable required for 4K content. C RS232 4-pin Control Connector. Transmits and receives serial data to and from serial controllable devices. For pin- out information, refer to the RS-232 Wiring se ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 16 of 38 4. Wiring and Connections 4.1. HDMI Cables Important items to consider when planning or installing a system using IP Video devices. – High quality HDMI cables are very important when passing UHD. Adding deep color and HDR raises the need for high quality cables. – Long HDMI cables can introduce signal degradation, so Savant recommends using th ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 17 of 38 4.5. IR Wiring PAV-VIMxS IR connections are made using a 3-pin Control Connector supplied with the device. The wire slips into the hole and locks with a screw located at the top of the connector. 3 2 1 PIN 1 IR - PIN 2 IR + PIN 3 Not Used Out G PAV-VOMVP1x IR connection are made using 3.5 mm IR Emitter supplied with the device. IMPORTANT: IR Wiri ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 18 of 38 4.7. Network The PAV-VIMxS uses a standard RJ-45 port complying with IEEE 802.3 Ethernet standards. This port is used for communication with the Savant Host. The VOMVP1x uses a shared Ethernet connection from its 10G connection. 4.8. AC Power Connection SURGE PROTECTION! Use a surge-protected circuit for all components and power supplies requirin ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 19 of 38 5. Installation 5.1. Install PAV-VIM8S/VIM4S The Savant IP Video Transmitter can be mounted in a 3U rack style enclosure and is compatible with all standard 19-inch NEMA rack mounts. The rack ears need to be attached prior to placing in a rack 5.2. Install PAV-VOMVP1x/VIMVP1x The Savant IP Video Receiver or Transmitter can be placed on a solid fla ...
Copyright © 2019 Savant Systems, LLC 009-1551-04 | 190717 20 of 38 5.3. Install PAV-VIM1C/VOM1C Wall Mounted To install the PAV-VIM1C/VOM1C the installer must remove two of the chassis screws on each side and use them to attach the included mounting brackets. Please follow the steps below. 1. Remove the two case screws in the center of the device (Shown in the image below). 2. Align the bracket using the top hole ...
