Sauder 402375 Manual 

Prefer the phone? Call 1-800-523-3987. Share your journey! sauder.com NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 397871 12/07/16 Purchased: _________ ...

Assembly Tools Required Part Identifi cation Hardware Identifi cation Assembly Steps Français Español Safety Warranty No. 2 Phillips Screwdriver Tip Shown Actual Size 2-3 4-5 6-22 23-25 26-28 29-30 31 Hammer Not actual size Skip the power trip. This time. A2 RIGHT END (1) B LEFT END (1) C2 RIGHT UPRIGHT (1) D2 LEFT UPRIGHT (1) E3 TOP (1 ...

A2 B C2 D2 E3 F2 G2 H I J K L M N R V2 W 12-1/2" 12-1/2" D260 D86 D707 D716 D78 D44 D45 D263 402375 www.sauder.com/services Page 3 ...

å Screws are shown actual size. You may receive extra hardware with your unit. 35DA CABINET RIGHT - 1 35DB CABINET LEFT - 1 35DC DRAWER RIGHT - 1 35DD DRAWER LEFT - 1 35AW CABINET RIGHT - 1 35AZ DRAWER LEFT - 1 35AY DRAWER RIGHT - 1 35AX CABINET LEFT - 1 45BA CABINET RIGHT - 1 45BD DRAWER LEFT - 1 45BC DRAWER RIGHT - 1 45BB CABINE ...

å Screws are shown actual size. You may receive extra hardware with your unit. BACKPLATE - 3 RR PULL - 3 SS LARGE DRAWER FRONT BRACKET - 2 TT FELT DISC CARD - 1 XX METAL PIN - 4 YY RUBBER SLEEVE - 4 ZZ BLACK 1-7/8" FLAT HEAD SCREW - 4 AAA BROWN 1" FLAT HEAD SCREW - 4 BBB BLACK 9/16" LARGE HEAD SCREW - 20 DDD BLACK 1/2" FLAT HEAD S ...

video assembly tip is available at www.sauder.com/services/tips å Assemble your unit on a carpeted fl oor or on the empty carton to avoid scratching your unit or the fl oor. å Push sixteen HIDDEN CAMS (MM2) into the ENDS (A2 and B), UPRIGHTS (C2 and D2), and BOTTOMS (G2 and H). Then, insert the metal end of a CAM D ...

and CABINET LEFTS (35AX, 35DB and 45BB) to the RIGHT END (A2) and UPRIGHTS (C2 and D2). Use twelve GOLD 5/16" FLAT HEAD SCREWS (GGG). Step 2 402375 www.sauder.com/services Page 7 Remember: Righty tighty. Lefty loosey. A2 D2 C2 Roller end Roller end Roller end GOLD 5/16" FLAT HEAD SCREW (12 used in this step ...

the BOTTOMS (G2 and H). Tighten eight HIDDEN CAMS. Step 3 402375 www.sauder.com/services Page 8 Start Tighten Arrow Minimum 190 degrees Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To compl ...

UPRIGHTS (C2 and D2), and BOTTOMS (G2 and H). Use six BLACK 9/16" LARGE HEAD SCREWS (DDD). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS, UPRIGHTS, and BOTTOMS. å Fasten the BASES (V2 and W) to the ENDS (A2 and B), UPRIGHTS (C2 and D2), and BOTTOMS (G2 and H). ...

and J). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACKS (I and J) to your unit using the NAILS (HHH). å NOTE: Be sure to tap NAILS into the holes that line up over the BOTTOMS (G2 and H). Step 5 402375 www.sauder.com/services Page 10 Finished surface Finish ...