Perlesmith PSTVMC03 Instruction Manual

Text of the manual

TV Cart Instruction Manual

Model:PSTVMC03 V3.0 Thank you for choosing this Perlesmith product! At Perlesmith we strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others on www.perlesmith.com/pages/reviews if you are satisfied. Should you have any issues, please don't hesitate

Minimum VESA pattern: 200mm/8 in.(W)x100mm/4 in.(H)

Check the VESA Pattern of Your TV before You Begin the Installation If your TV VESA is greater than 600x400 mm/23x16 in. or less than VESA 200x100 mm/8x4 in., this TV cart is NOT compatible. If this TV cart is NOT compatible, please contact customer service at [email protected] to find a compatible

G (4pcs) H (8pcs)

M6/M8 Washer 2.5mm Spacer I (4pcs) J (4pcs) 10mm Spacer 22mm Spacer Hardware for Attaching TV Brackets to TV A1 (4pcs) M6x12mm A2 (2pcs) H2 (1pc) J2 (2pcs) F2 (1pc) G2 (1pc) Wrench (1pc) Cable Tie (3pcs) I1 (1

A2(2pcs) B2(2pcs) C2(1pc) A1(4pcs) I1(1pc)

Please tighten the bolts [A1] A1 I1 B2 A2 C2 STEP 1 Assemble the Base STEP 1-1 STEP 1-2 Slide the tube and pole connector [C2] onto the square tubes [A2]. Secure the base using bolts and washers [A1]. Attach casters [B2] to the square tubes [A2] using the provided allen key [I1]. Back Front Back Front Wrench 4mm [I1

D2(2pcs) B1(2pcs)C1(2pcs) J1(1pc)

Secure Pole Assembly to Base STEP 2 Step 2-1 Adjust the height of the pole assembly. Step 2-1-1 Loosen the knobs then stretch the upper poles from the lower poles. Step 2-1-2 Adjust the upper poles to your desired height. Step 2-1-3 Insert the latches [L] into the holes nearest to the connecting part of upper pole and lower

Step 2-2 Secure the 2pcs poles assemblies [D2] to the tube and pole connector [C2]

using bolts and ring [B1], washers with 3 holes [C1] and Allen key [J1]. L K 5mm [J1] Allen Key 05

E1(4pcs) H2(1pc) I2(1pc) D1(4pcs) J1(1pc)

Install the Square Plate to Upper Poles STEP 3 Secure the square plate [I2] to the support plate [H2] via the holes on the upper poles using bolts and washers [D1] and nuts [E1]. Back Front J1 D1 D1 I2 H2 E1 5mm [J1] Allen Key 06

Select TV Bolts

Select Spacers (if needed) Only one bolts size fits your TV. WITH SPACER a Long Bolt Short Bolt Washer Washer Spacer TV Bracket TV Bracket EXTRA 03

Secure the TV Brackets to Your TV

Alternate Spacer Setups With Spacer b 03 No Spacer a 03 03 01 01 02 3 For Rounded TV For Flat TV with: Inset Holes Cable Interference For Flat TV Spacer not necessary J2 J2 H1 Note: Remove the pre-assembled nuts [S] on the brackets, then secure the knobs [H1] to the brackets. STEP 4D Secure the Knobs [H1] to the Brackets [J2

HEAVY! You may need

assistance with this step. Secure the TV onto the Square Plate STEP 5 Phillips Screwdriver Step 5-1 Hang the TV with brackets to the square plate. Step 5-2 Push the bottom of the TV to square plate. Step 5-3 Tighten the bolts preassembled on the brackets until the bolts touch the square plate. 09

Other TV Mount Manuals