Moons' MSSTAC6 Operation & User’s Manual

Text of the manual

- 2 -

MOONS’ MSSTAC6 Step Motor Drive User Manual MOONS’ www.moons.com.cn Contents 1 Introduction ....................................................................................... - 3 - 1.1 Overview ................................................................................... - 3 - 1.2 Features ................................................

- 3 -

MOONS’ MSSTAC6 Step Motor Drive User Manual MOONS’ www.moons.com.cn 1 Introduction 1.1 Overview Thank you for selecting a MOONS' motor drive. We hope our dedication to performance, quality and economy will make your motion control project successful. If there’s anything we can do to improve our products or help you use them better, please call (8

- 4 -

MOONS’ MSSTAC6 Step Motor Drive User Manual MOONS’ www.moons.com.cn 1.3 Block diagram 1.4 Specifications POWER AMPLIFIER SECTION: MSSTAC6-S, MSSTAC6-Q, MSSTAC6-I AMPLIFIER TYPE MOSFET , Dual H-Bridge, 4 Quadrant CURRENT CONTROL 4 state PWM at 20 KHz OUTPUT CURRENT 0.5 — 6.0 in 0.01 amp increments POWER SUPPLY Line operated nominal 120VAC, 50/60Hz

- 5 -

MOONS’ MSSTAC6 Step Motor Drive User Manual MOONS’ www.moons.com.cn POWER AMPLIFIER SECTION: MSSTAC6-S-220, MSSTAC6-Q-220, MSSTAC6-I-220 AMPLIFIER TYPE MOSFET , Dual H-Bridge, 4 Quadrant CURRENT CONTROL 4 state PWM at 20 KHz OUTPUT CURRENT 0.5 — 3.2 in 0.01 amp increments POWER SUPPLY Line operated nominal 120-240VAC, 50/60 Hz DC BUS VOLTAGE Nomi

- 6 -

MOONS’ MSSTAC6 Step Motor Drive User Manual MOONS’ www.moons.com.cn and maintenance INTERFACE RS-232 and RS-485 Bus ENCODER Differential line receivers suitable for 200 KHz or greater OPERATING TEMPERATURE 0-55°C (32 - 158°F) ambient temperature HUMIDITY 90% non-condensing 1.5 Getting Started To use drive models MSST5-S or MSST10-S, the following

- 7 -

MOONS’ MSSTAC6 Step Motor Drive User Manual MOONS’ www.moons.com.cn 2.1.2 Connecting the Motor Never connect the motor to or disconnect it from the drive. Insulate unused motor leads separately, and then secure. Never connect motor leads to ground or to a power supply. Four lead motors can only be connected one way, as in the drawing below: Six le

- 8 -

MOONS’ MSSTAC6 Step Motor Drive User Manual MOONS’ www.moons.com.cn Note: NC = not connected Eight lead motors can also be connected in two ways: series and parallel. As with six lead motors, series mode will provide more torque at low speeds and less torque at high speeds. When connected in series, the motor should be operated at 30% less than the

- 9 -

MOONS’ MSSTAC6 Step Motor Drive User Manual MOONS’ www.moons.com.cn RS-485/422 allows more than one drive to be connected to a single host PC, PLC or other computer with an RS-485/422 port. It also allows the communication cable to be long (more than 1000 feet [300 meters]). A Short tutorial on RS-485 & RS-422 RS-485, in the strictest definition, i

- 10 -

MOONS’ MSSTAC6 Step Motor Drive User Manual MOONS’ www.moons.com.cn To connect RS-485 to a 25 pin serial port, a converter is required. Part number 117701 from Jameco Electronics (www.jameco.com) is recommended. If the PC has a 9 pin serial port, a Jameco cable #31721 is also required. Connect as follows: adaptor drive 1 RX+ 2 RX- 3 TX- 4 TX+ Set

Other DC Drives Manuals