Midland 70-0671 Alignment Procedure
Text of Midland 70-0671 Alignment Procedure
70-0671 Alignment Procedure
SETUP
1
Remove the six securing screws from the bottom cover , and the cover itself.
2
Connect a resistive 50 Ω RF load and wattmeter to Antenna Connector J502.
3
Connect 13.4V DC power to transceiver J505.
4
Connect a 3.2 Ω, 20W resistor to pins 4 and 6 of the Accessory Plug. The jumper
between pins 5 and 6 must be temporarily removed to make this connection .
The resistor serves as a constant load to replace the speaker’
Midland 70-0671 4 Initiate transmit on any channel. Measure transmitted RF carrier frequency
without modulation and, if necessary, adjust REFERENCE OSCILLATOR X701
for carrier frequency to within ±30Hz of channel frequency.
PA MODULE ALIGNMENT
The 70 -0671 should be adjusted to have a 6 MHz channel spread (8 MHz C-Band)
at 110W. To do so :
1 Change the TX test frequency to the desired frequency.
2 Activate transmit mode and measure RF power at
8 Adjust RV401 for ±750 Hz ± 100 Hz (wide) or ± 375 Hz ± 100 Hz (narrow)
deviation.
9 Change the transmit DCS code +023 to the transmit test by testing frequency
using the programmer.
10 Adjust RV401 so that modulation waveform from modulation analyzer matches
the correct waveform shown in Figure 2-1.
11 Change 250.3 Hz CTCSS tone to the transmit test by testing frequency using the
programmer. Carefully adjust RV401 for ± 750 Hz ± 10 Hz
Change the RX test frequency to 33.0 MHz for A-Band radios, 39.0 MHz for
B-Band , 46.0 MHz for C-Band.
•First Injection
2 No adjustment for first injection is required.
•Preselector Alignment
3 No adjust ment for the preselector (L201, L202, L203, L204, L205, L206, L207,and
L208 ) is required.
•Quadrature Detector
4 No adjustment for the quadrature is required.
•First IF
5
Apply enough modulated ( by 1KHz tone at ± 3KHz
7 Temporarily disable the pulse generator.
8 Using coax cable of minimum convenient length, connect the pulse generator,
the RF signal generator, and the radio to the two-way power divider.
9 Disable the noise blanker by placing SW801 to the OFF position.
10 Apply an on -channel signal to obtain12dB SINAD, then increase the RF generator
output by 40dB.
11 Enable the pulse generator to produce the 10nsec pulses. Adjust pulse amplitude
to return
• Tight Squelch
15
Squelch level set maximum ( 80 ). by using the front UP / DN switch
16
Apply 0.95 uV of modulated standard deviation on -channel RF signal to the 50 Ω
antenna connector.
Adjust Squelch range RV201 counter-clockwise just until squelch opens ( audio
on ).
Figure 2-2 Adjustment Map TR -055 Board
L702
L713
L804
L803
L801
L802
L217
L215
X701
VC
RV201
RV401
Complete realignment is only needed when a component that affects alignment has been replaced. RADIO
REPROGRAMMING WITH TEST FREQUENCIES IS REQUIRED.
Table 2-1 TEST EQUIPMENT REQUIRED
TEST INSTRUMENT
INSTRUMENT CAPABILITIES
USE
Regulated
DC Power supply
RF Wattmeter
RF Load Resistor
Frequency
Modulation Meter
Frequency Me ter or
Frequency Counter
Audio Generator
RF Signal
Generator
Distortion Analyzer
Load Resistor
( audio )
AC Voltm