Yamaha ProR3 Owner's Manual

Text of Yamaha ProR3 Owner's Manual

PRE EFFECT EQ

DIGITAL REVERBERATOR Owner

Yamaha ProR3 FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be u

ProR3 Digital Reverberator

Precautions Water warning Do not expose the device to rain, use it near water or in damp or wet conditions, or place con- tainers on it containing liquids which might spill into any openings. Avoid excessive heat, humidity, dust, and vibration Keep the unit away from locations where it is likely to be exposed to high temperatures or humidity – such as near radiators, stoves, in direct sunlight, etc. Avoid locati
ProR3 Digital Reverberator Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Rear panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Basic use – using a preset program – . . . . .7 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Turning the power on (off). . . . . . . . . . . . .
ProR3 Digital Reverberator Introduction Thank you for purchasing the Yamaha ProR3 Digital Reverberator. The ProR3 marks a new era in Yamaha’s reverberation technology. Third-generation Yamaha digital signal processors (DSP) with 32 bit digital signal processing and high-performance 20 bit linear A/D and D/A convert- ers provide unprecedented density and resolution, with breathtakingly dynamic impact. The ultra-high quality analog input a

2 Front panel

ProR3 Digital Reverberator Front panel 1 INPUT level meters (L/R) This is a stereo LED meter with 8 segments for each channel. The segments respectively indicate levels of –36 dB, –24 dB, –18 dB, –12 dB, –9 dB, –6 dB, –3 dB, and CLIP. 2 PROGRAM number display This is a two-digit seven-segment display that indicates the currently selected program number. If this display is blinking, a new program has been selected but its conte

Front panel 3

ProR3 Digital Reverberator 5 DATA/CURSOR keys The DATA keys (INC) (DEC) are used to modify the value of the selected parameter. The CURSOR keys (√) (®) are used to select parameters displayed in the LCD. When the PROGRAM indicator is lit, the DATA keys are used to select the program that you wish to recall. 6 PARAMETER keys These keys select effect parameters. Each time a key is pressed, it will cycle through the parame- ter pages, and w

4 Front panel

ProR3 Digital Reverberator 7 Numeric keys These keys are used to directly input the number of a program that you wish to recall, or to input parameter values. When you use the numeric keys to input a parameter value, the value will blink until it is final- ized. Press the RECALL/ENTER key to finalize the value. To return to the original value, press the CANCEL key. Some parameters cannot be entered using the numeric keys. To specify a neg

Front panel 5

ProR3 Digital Reverberator 11 PRE EFFECT EQ, ON controls This is a three-band parametric equalizer that equalizes the signal before the effect. The center frequency and gain can be set for each band. The ON key turns the pre-effect equalizer on/off. When the equalizer is on, the green indicator will light. 12 COMPARE key After editing the parameters of a program, you can use this key to compare the edited sound with the sound of the program

6 Rear panel

ProR3 Digital Reverberator Rear panel 15 MIDI connectors These are 5 pin DIN type standard MIDI IN, MIDI OUT, and MIDI THRU connectors. These connectors are used when transmitting program change messages or control change mes- sages from an external MIDI device to the ProR3, or when transmitting program bulk dump data from the ProR3 to another device. 16 OUTPUT jacks These are balanced output jacks which output the analog return signal to yo

Yamaha ProR3 Basic use – using a preset program – 7

ProR3 Digital Reverberator Basic use – using a preset program – Here’s how to select a preset program and use it without adjusting any parameters. Connections 1. Connect the sound source to the INPUT jacks. For a stereo sound source, connect the outputs of both channels to the INPUT jacks. For a mon- aural sound source, use the L input jack. If the sound source has XLR connectors, make connections using th

Yamaha ProR3 8 Basic use – using a preset program –

ProR3 Digital Reverberator Adjusting the input level When the power has been turned on for the ProR3 and the other equipment, make the sound sources produce sound, and adjust the input level of the ProR3. 1. Rotate the INPUT level controls while watching the INPUT level meters. Set the levels to achieve maximum S/N ratio while not allowing the CLIP indicators to light. Selecting effect programs There are two way

Basic use – using a preset program – 9

ProR3 Digital Reverberator Preset Program List No. Title Type Description Large Hall 1 Large Hall 1 Reverb The ProR3’s standard hall-type reverb. Simulates a large hall with good acous- tics, and is suitable for any instrument. 2 Large Hall 2 Reverb 3 New Hall Reverb A program with a slight delay between the sparse early reflections and the rich reverberation. 4 Wide Hall Reverb A program simulating a spaciou

10 Basic use – using a preset program –

ProR3 Digital Reverberator Special Room 37 Power Drum Room RoomSim Adds a strong live ambiance to drums. Try it on sampled drums. 38 Soft Space Rev+Cho A percussive short reverb with chorus added. Gives ambiance to drums, lead instruments, and vocals. 39 Droid Short Reverb Simulates an early and extremely expensive digital reverb unit. 40 Droid Long Reverb 41 Tile Room RoomSim The bright ambiance of a tiled roo

Basic use – using a preset program – 11

ProR3 Digital Reverberator 77 Super Long Decay Reverb An effect like an extremely long tunnel. 78 Slow Pan Reverb Rev→Pan A fairly long reverb is panned slowly. 79 Sub Aqua Pit→Rev Water sounds producing a “sprong” when applied to a rim shot. When applied to strings, a saw-like sound results. 80 Thud Pit→Rev Turns an acoustic instrument into a synth! Produces an auto-wah like effect when applied to gu

12 Advanced uses (1)

ProR3 Digital Reverberator Advanced uses (1) The bypass function When you press the BYPASS key, the circuit will be switched so that the input sound is output directly. This function provides an easy way to make a quick comparison between the sound pro- cessed by the effect program and the unprocessed sound. When the effect is bypassed, the red indicator will light. Pre-effect EQ The PRE EFFECT EQ controls allow you to make settings

Yamaha Amplifier Owners Instructions: