Yamaha REV500 Operation Manual

Text of Yamaha REV500 Operation Manual

Yamaha REV500 FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be us

• Connect this unit's power cord only to an AC outlet of the

type stated in this Owner's Manual or as marked on the unit. Failure to do so is a fire and electrical shock hazard. • Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock may result. • Do not place a container with liquid or small metal objects on top of this unit. Liquid or metal objects inside this unit are a fir

Front Panel .................................................................... 1

Rear Panel ..................................................................... 2 Installation and Connections ........................................ 2 Using the REV500 ...........................................3 Selecting Programs ....................................................... 3 Testing Progr

1 INPUT LEVEL control and meter

The INPUT LEVEL control sets the input level for both the right and left input channels. It is accompanied by a stereo LED meter that shows the levels of the signals received by the REV500 after A/D conversion. Lighting of the red CLIP LEDs thus indicates clipping of the digital signal. You should adjust the control so that the CLIP LEDs do not light. 2 PROGRAM keys These keys let you choose the program that the R

Installation and Connections

Before attempting to use your REV500, make sure that you have carefully read and understood the precautions inside the front cover of this manual. Mount the REV500 in a rack, or place it in a location where it is safe and stable. Make sure that the POWER switch is off before making any connections. Plug in the power cord, and connect the REV500’s input and output connectors to your mixer, multitrack recor

Using the REV500

Testing Programs AUDITION key You can use the REV500’s handy audition function to check the effect produced by a program when it’s inconvenient to run your actual sound source through the REV500. Just press the AUDITION key in the upper right corner of the front panel. The REV500’s internal tone generator will produce a tone that lets you hear how the program you’ve selected affects the output sound. You can select one of two sam

Standard hall-type reverbs that simulate large halls with good acoustics. May be

used with any instrument. “Large Hall 1” is bright; “Large Hall 2” is slightly darker. A reverb that simulates the feel of a large hall with no audience. A bright reverb with breadth, thanks to slightly emphasized early reflec- tions. A reverb with the low-range characteristics of an arena-sized concert space. A bright reverb with a punch. A light, bright

Yamaha REV500 A reverb that simulates a large room with hard walls, for a slightly quirky

thick sound. A large room reverb, slightly drier than “Large Room 1.” A room reverb with a very live nonlinear sound. Good with drums and guitars. Reverbs that simulate the sound of a room with live acoustics. Use “Live Room 1” to simulate greater distance from the sound source, or “Live Room 2” for front-row seats. A simulation of the reverb in a til

A simulation of a metal plate echo effect.

A bright, highly dense plate reverb. The bright, transparent plate sound that is popular on the West Coast. A spring reverb simulation with a longish pre-delay. A rather coarse reverb with extra low-range energy. Good with vocals and solos. A bright, light plate sound. The plate echo that would be created by an extremely thin metal plate. Complex reverb with a sub-reverb tail (when INPUT SELECT is se

A short reverb combined with a flanger. Good with organs, strings, etc.

Short reverbs combined with chorus. The longer pre-delay of “Chorus Circles” emphasizes the sense of separation between the reverb and chorus effects. A flanger-like effect with a resonance point that varies with the input level. A reverb with the resonance point set at E. Four variations on the reverb/flanger theme. The flanger effect becomes more pronounced as the p

Editing Basic Parameters

REVERB Time REV TIME PRE DELAY E/R DLY ER LEVEL Early Reflections Reverb Time x LO-RATIO HI-RATIO Frequency 1.0 The four PARAMETER EDIT controls on the REV500’s front panel let you adjust the basic program parameters quickly and easily. When you rotate one of these controls, the program information in the LCD (shown above) will be replaced by a graphic display indicating how the changes you’ve made have affec

Changing the Effect Level

You can also use the ER LEVEL control to adjust the effect level, that is, the level of the total effect output. To do so, press the EFF LEVEL key before turning the ER LEVEL control. The LED above this key will light, and (as with the other basic parameters) the program information in the LCD will be replaced by a graphic display. You can set a level from 0 to 100. Realtime Parameter Control The REV500 also lets you dynamically

0.1 — 2.4

Low frequency reverb time, proportional to REV TIME DIFFUS 18 0 — 10 Spread of reverb sound HPF 19 THRU, 20 — 1.0k [Hz] Cutoff frequency of high pass filter LPF 20 THRU, 500 — 20k [Hz] Cutoff frequency of low pass filter REVERB The parameters in the following table are available for simple reverb effects. Parameter Ctrl. No. Range Description DENSITY 21 0 — 100 [%] Density of reverber

REVERB ➔ DYNAMIC FILTER

In this effect type, the output from the reverb is fed into a dynamic filter. Parameter Ctrl. No. Range Description SENS 28 1 — 10 Sensitivity of the resonator input signal RESO 29 0 — 100 [%] Resonator feedback level DECAY 30 6 — 24000 [ms] Speed of resonance point return to lowest frequency MIX 31 0 — 100 [%] Balance of reverb direct output and resonator output REVERB ➔ RESONATOR In this effect type, the output from

0.05 — 10.00 [Hz]

Modulation frequency DEPTH 75 0 — 100 [%] Modulation depth FB LVL 76 0 — 100 [%] Feedback level (REVERB ➔ FLANGER effects only) MIX 77 0 — 100 [%] Cutoff frequency of low pass filter REVERB ➔ CHORUS, FLANGER or SYMPHONIC In these effect types, the output from the reverb is fed into a chorus, flanger, or symphonic effect. Parameter Ctrl. No. Range Description SPEED 74 0.05 — 1

Yamaha REV500 REVERB ➔ TREMOLO

In this effect type, the output from the reverb is fed into a tremolo effect. Saving Edited Programs Parameter Ctrl. No. Range Description FB LVL 82 -100 — +100 [%] Level of feedback to own channel CROSS FB 83 -100 — +100 [%] Level of feedback to opposite channel ECHO ➔ REVERB In this effect type, the output of the reverb’s PRE DELAY block is fed back into the reverb input to produce an echo effect. Parameter Ctrl. No. Range D

Yamaha REV500 Selecting an Input Mode

If you will be using the REV500 to process monophonic input (from the left input connector), you must use the INPUT SELECT function to inform it of this fact. To change the input mode, first press the UTILITY key. If necessary, press the UTILITY key again until the INPUT SELECT display appears: Stereo input Mono input Use the REV TIME control to switch between the STEREO and L-MONO input settings. When you have m

Adjusting the Audition Function

The REV500 lets you customize the audition function to suit your needs. You can select one of two tones: either a snare drum or a rim shot. You can also specify whether pressing the AUDITION key will play the selected tone once, or start it playing repeatedly. You can also turn the function off, to prevent the REV500 from producing unwanted sounds if this key is pressed accidentally. To adjust the audition function, first

Using MIDI Functions

Selecting a MIDI Channel You can change the MIDI channel that the REV500 uses to transmit and receive data. First, press the UTILITY key. If necessary, press the UTILITY key again until the MIDI CHANNEL display appears: MIDI channel setting Use the REV TIME control to select the desired MIDI channel. You can set the REV500 to use any of channels 1 through 16, or select OMNI for all channels. You can also select OFF to disable MIDI c

Yamaha Amplifier Owners Instructions: