NEXERa 3360162 Assembly Instructions Manual
Text of NEXERa 3360162 Assembly Instructions Manual
Email / Courriel
Monday to Friday
7:30 AM - 4 PM - Eastern Time
Lundi au vendredi
7:30h à 16h - Heure normale de l’Est
www.nexeradistribution.com
Webpage / Page web
1 877 629-9022
CANADA / USA
Assembly instructions
Instructions d’assemblage
nexeradistribution.com
65-3360162_R1
Lot #
Online resources
Ressources disponibles en ligne
How-to videos
Vidéos d’aide
FAQ’s
Questions fréquentes
Order replacement parts
Comma
Read these assembly instructions carefully before beginning. Verify that you have in
hands all the wood parts and hardware. Keep this document for future reference.
Lisez attentivement ce guide d’assemblage avant de débuter. Assurez vous que toutes les
composantes de bois et de quincaillerie sont présentes. Conservez ce document.
Two people are required to assemble and move this unit.
Deux personnes sont requises pour
Liste de quincaillerie
8x
# 0111
2x
# 2154
set of 2 parts
ensemble de 2 pièces
1x
# 0601
# 1505
1x
# HH510
1x
KIT
Part A
Partie A
Part B
Partie B
# 2152
2x
KIT
Discard
Jetez
Insert the 38 cam locks # 0203 into the panels A1, B1, E1, F, G, H1, J, M and N
Insérez les 38 excentriques # 0203 dans les panneaux A1, B1, E1, F, G, H1, J, M et N
Pressez fermement dans la cavité
VIDEO
# 0203
38x
A1
B1
H1
E1
J
J
N
F
G
G
M
M
Add a protection under
the parts on all assembly steps
Ajoutez une protection sous
les pièces à chaque étape
2 Installez 26 boulons # 2200 dans les panneaux A1, B1, C et E1
Install 26 push bolts # 2200 into t
Use the 2 screws # 0101 to fasten the magnet # 1505 to the panel H1
# 0101
2x
# 1505
1x
E1
First, use 8 screws # 0105 to fasten the 2 mounting plates included in the push-to-open
device kits # 2152, to the panel E1. The small tab located on the rear of the plate must be
aligned towards the back of the panel. Finalize the step by snapping-in each push-to-
open device into the mounting plate, from the side
poussoir à ressort # 2152 sur le panne
2x # 2223
6x # 0105
6
front edge of the hinges with the front edge of the panel E1
Utilisez 6 vis # 0105 pour installer les 2 charnières à rabat # 2223 (partie B) sur le panneau E1.
Alignez la partie avant des charnières avec le chant avant du panneau E1
E1
Part B
Partie B
Insérez la charnière
en premier
E
Fasten the panel F to the panel E1. Then, tighten the 2 cam locks # 0203 located on
the panel F
Assemblez le panneau F avec le paneau E1. Serr
Fasten the 2 panels J and the panel N to the panel A1. Then, tighten the 6 cam locks # 0203
located on the panels J and the panel N
Assemblez les 2 panneaux J et le panneau N avec le panneau A1. Serrez ensuite les 6 excentriques
# 0203 se trouvant sur les panneaux J et le panneau N
8
Reference holes here
Perçages de référence ici
J
J
N
Hole here
Perçage ici
A1
Bottom of unit
Bas de l’unité
Tournez vers la droite 2/3 de tour
et serrez fermement
Fasten the panel B1 to the assembled unit. Then, tighten the 4 cam locks # 0203 located
on the panels E1 et H1. You will later stand the unit and tighten the 6 cam locks located
on the back face of the panels J and N (step 12)
Assemblez le panneau B1 avec l’unité. Serrez ensuite les 4 excentriques # 0203 se trouvant sur les
panneaux E1 et H1. L’unité sera relevée plus tard pour serrer les 6 excentriques se trouvant sur les
la partie arri�
Fasten the panel C to the assembled unit. Then, tighten the 4 cam locks # 0203
located on panels A1 and B1. Finalize the step by adding the 10 caps # 0547 to
the cam locks # 0203 located on the panels A1, B1, F and H1
Assemblez le panneau C avec l’unité déjà assemblée. Serrez ensuite les 4 excentriques
# 0203 se trouvant sur les panneaux A1 et B1. Terminez l’étape en installant les 10
capuchons # 0547sur les excentriques # 0203