Warwick ProTube IV Owner's Manual

Text of Warwick ProTube IV Owner's Manual

Congratulations on the purchase of the

new Warwick amplifier head/combo. Please read these instructions through before connecting and operating the device. If you keep to the guidelines set out in this manual, you will soon be able to appreciate the quality of this new Warwick amplifier. Please keep this instruction booklet handy in case you need to consult it again. Please send the PASSPORT to the address indicated therein. The following recommenda

Pro Tube IX

23 GROUND LIFT switch isolates the earth connection from the ground of signal. Should several devices be simultaneously connected to earth by the same conductor as well as via line connections, a so called hum loop might appear. In this case operate GROUND LIFT to eliminate the current hum. DI PRE/POST switches the signal lying at the DI OUT sockets. PRE the unmodified bass signal is retained on both DI OUT sockets, POST the tone control and ef
Pro Tube IX DI OUT LEFT and DI OUT RIGHT sockets for supplying a stage or studio mixing console. TUNER OUT socket for the connection of a tuner. When MUTE mode is activated, the unmodified bass signal is retained here. MONO LOOP for the serial insertion of dynamic effects units (e.g. compressor, auto wah, etc.). Connect SEND with the input and RETURN with the output of the effects device. PARALLEL STEREO LOOP: the degree to which external effects influe
Pro Tube IX 25 This channel is equipped with two tubes. One preamp tube is always included within the signal flow. 2ND STAGE switch adds one output stage tube into the circuit. This feature offers the choice between a so called hybrid amplifier (tube preamp with transistor power amp) and the sound of an all tube amplifier head. CONTOUR switch boosts bass and treble at once. CRUNCH control adjusts the tube pre- amplification. TONE control sets the basic sou
Pro Tube IX EXAMPLES These setting examples aim at helping you to better handle with the control stage and to utilise it for the realisation of your sound conceptions. Set channel 1 according to the examples and adjust the TONE control to the left and to the right within the suggested area, respectively. press the switches to learn more about their efficiency. CRUNCH settings are level-dependent. The examples suppose GAIN has been set to OK. As Rock-par
Pro Tube IX 27 Two switches LOW BOOST and HIGH BOOST to pre-adjust the basic sound characteristics. Ten faders 35/70/140/210/420/730/1.2k/2.5k/5k/10k Hz to amplify/soften the respective frequency band by +/-12 dB. You should generally adjust the graphic EQ to approximately 0 dB. This means boosts and cuts should be effected with moderation. When adjusting the faders mostly within the positive area (1) the OL LED of the master section might illuminate, whic

Pro Fet III

25 mV transistor, active controlled none fan cooled (non permanent) bass, punch, param. mids with freq. and level controls, attack, treble, low boost and high boost switches. Dyn. control with switchable limiter none 200 Ω 0 dB, 600 Ω mono serial send 0 dBu, 600 Ω return 0 dBu, 10 kΩ ground lift, DI pre/post none none 250 W/4Ω jack XLR & Speakon <0.1% 11,5 19“/483x90x375 Pro Fet IV 25 mV transistor, active controlled none fa

Warwick GmbH&Co.Music Equipment KG•Gewerbegebiet Wohlhausen•08258 Markneukirchen/Germany•Tel 0049-(0)37422-555-0

Fax 0049-(0)37422-555-99 • Send us an E-Mail to: [email protected] • Visit us on the World Wide Web: http://www.warwick.de Branch China: Warwick Music Equipment (Shanghai) Ltd., Co.Shanghai Waigaoqiao Free Trade Zone • Shanghai 200131 / P.R.China

Warwick Amplifier Owners Instructions: