KidKraft WINDALE Installation And Operating Instructions Manual

8-10 Hrs To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer to these instructions often and give them to any future owner of this play system. Manufacturer contact information provided below. OBSTACLE FREE SAFETY ZONE - 24’11”x 26’ (7.348m x 7.924m) area requires Protective Surfacing. See page 3. MAXIMUM VERTICAL FALL HEIGHT - 6’5” CAPACITY - 9 Users M ...

CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system. Go over the warnings and safe play instructions ...

protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever product you select, follow these guidelines: Loose-Fill Materials • Maintain a m ...

sand and repaint using a non-lead paint complying with 16 CFR 1303. Inspect and tighten all hardware. On wood assemblies DO NOT OVER- TIGHTEN as to cause crushing and splintering of wood. Check for sharp edges or protruding screw threads, add washers if required. SHOCK ABSORBING SURFACING: Check for foreign objects. Rake and check depth of loose fill protective surfacing materials to prevent compact ...

KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set. What causes weathering? Does it affect the strength of my Play System? One of the main reasons for weathering is the effects of water (mois ...

attention. Improper assembly could lead to an unsafe or dangerous condition. Where this is shown, 2 or 3 people are required to safely complete the step. To avoid injury or damage to the assembly make sure to get help! Check that assembly is square before tightening bolts. Use a measuring tape to assure proper location. Check that set or assembly is properly level before proceeding. Pre-drill a pilot hole ...

KIDKRAFT DESIGN HARDWARE For example: BOLT LENGTH 4½ (4.5) inches long 114mm long 1 inch = 25.4mm 25.4mm 4.5 inches x DIAMETER CONVERSION LENGTH CONVERSION = BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm For example: HARDWARE LENGTH CHART inches vs millimetres 6 152 5½ 140 5 127 4½ 114 4 102 3½ 89 3 76 2½ 64 2 51 1½ 38 1¼ 32 1-1/8 29 1 25.4 7/8 22 3/4 19 1/2 12.7 1/4" (6mm) Flat Washer 1/4" (6mm) Lock Washer 1/4 ...

1 x 4 1 x 5 1 x 6 1 x 3 1/2 x 4 5/4 x 6 5 1/2" 139.7 1" 25.4 11.1 .44 82.6 3 1/4" 4 x 4 3 1/2" 88.9 3 1/2" 88.9 4 1/2" 114.3 5/8" 15.9 15.9 5/8" 1 3/8" 34.9 2 x 6 5 3/8" 136.5 1 1/2" 38.1 15.9 5/8" 3 3/8" 85.7 60.3 2 3/8" 15.9 5/8" 1505mm KIDKRAFT DESIGN WOOD PROFILES LENGTH CONVERSION For example: 1 inch = 25.4mm BOARD LENGTH 59¼ (59.25) inches 59.25 inches x 25.4mm = Dimensions in brackets [mm] represent millimetres. 5/4 x 4 3 1/2" 88.9 1" ...

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 1pc. - 2231 - Door Arch 1/2 x 4 1/2 x 15-7/8" - Box 2 - 3602231 12pc. - 2227 - Wall Board 1/2 x 4 x 22" - Box 2 - 3672227 24pc. - 1930 - Siding 3/8 x 3-1/2 x 41-1/2" - Box 2 - 3671930 6pc. - 2220 - Siding 3/8 x 3-1/2 x 33" - Box 2 - 3672220 9pc. - 2219 - Siding 3/8 x 3-1/2 x 20" - Box 2 - 3672219 3pc. - 2232 - Door Siding 3/8 x ...

1pc. - 2211 - Floor End 1 x 5 x 35-1/4" - Box 2 - 3672211 1pc. - 2200 - Back Divider 1 x 4 x 39-3/16" - Box 2 - 3672200 Actual Size " x 3 " " x 4½" " x 5 " Nominal Size 1 x 4 1 x 5 1 x 6 Part Identification (Reduced Part Size) 2pc. - 2226 - Wall Board 1 x 5 x 20" - Box 2 - 3672226 2pc. - 2217 - Seat Support 1 x 4 x 35-7/8" - Box 2 - 3672217 1pc. - 2221 - Side Ground 1 x 4 x 35-7/8" - Box 2 - 3672221 2pc. ...

1pc. - 2209 - Door Stop 5/4 x 3 x 10" - Box 2 - 3672209 1pc. - 2208 - Centre Gap Board 1 x 6 x 35-3/4" - Box 2 - 3672208 Actual Size " x 5 " 1" x 1 " 1" x 2½" 1" x 3½" 1" x 4½" 1" x 5½" Nominal Size 1 x 6 5/4 x 2 5/4 x 3 5/4 x 4 5/4 x 5 5/4 x 6 Part Identification (Reduced Part Size) 2pc. - 2201 - Café Gusset 5/4 x 2-1/4 x 8" - Box 2 - 3672201 4pc. - 2206 - Cedar Floor Board 1 x 6 x 35-3/4" - Box 2 - 36 ...

Part Identification (Reduced Part Size) Actual Size 1½" x 1½" 1 " x 2½" 1 " x 3 " 1½" x 5 " Nominal Size 2 x 2 2 x 3 2 x 4 2 x 6 2pc. - 0367 - Floor Gusset 2 x 3 x 11" - Box 2 - 3670367 1pc. - 0369 - Lower Diagonal 2 x 3 x 37" - Box 2 - 3670369 4pc. - 1424 - Roof Support 2 x 3 x 40" - Box 2 - 3671424 2pc. - 0349 - Rock Rail 2 x 3 x 51" - Box 2 - 3670349 1pc. - 4919 - SW Rail Block 2 x 4 x 5-3/8" - Box 2 - ...

- 1pc. 2058 - Door Side Left 1 1/4 x 3 x 40 1/8 " - Box 2 - 3602058 1pc. - 2057 - Door Side Right 1 1/4 x 3 x 40 1/8 " - Box 2 - 3602057 1X 3320386 Rocks (5pk) 3-Green 2-Yellow 1X 9320146 Small Window (Green) 1X 9320374 KidKraft I.D Plaque w hardware 1X 3320165 6 Pane Arch Window (2 Pk) 2X 3724943 42" Belt Swing Yellow w.welded chain 1X 3200184 Triangle Plate (4pk) Green 1X 3200202 Glider Hanger (2pk) 1X 320 ...

3pc. LS3 - Lag Screw 1/4 x 3" - (9262230) 4pc. LS1 - Lag Screw 1/4 x 1-1/2" - (9262212) 4pc. G7 - Hex Bolt 5/16 x 5-1/2" - (9277352) 1pc. H8 - Hex Bolt 1/4 x 4-1/4" - (9277241) 2pc. H5 - Hex Bolt 1/4 x 4-1/2" - (9277242) Hardware Identification (Actual Size) 4pc. G1 - Hex Bolt 5/16 x 1-1/2" - (9277312) 4pc. H7 - Hex Bolt 1/4 x 5-1/2" - (9277252) 6pc. H4 - Hex Bolt 1/4 x 4" - (9277240) 5pc. G4 - ...

52pc. LW1 - 1/4" Lock Washer - (9253200) 5pc. S10 - Pan Screw #8 x 1" - (9264510) 177pc. S0 /S22 - Truss Screw #8 x 7/8" - (9229505) 20pc. S7 - Pan Screw #12 x 2" - (9264620) 47pc. TN1 - 1/4" T - Nut -(9285200) 12pc. LN2 - 5/16" Lock Nut - (9283300) 16pc. FW0 - 3/16" Flat Washer - (9251100) 6pc. PB2 - Pan Bolt 1/4 x 1-1/4" - (9274211) Hardware Identification (Actual Size) 54pc. FW1 - 1/4" Flat Washe ...

• Please refer to Page 6 for proper hardware assembly. • Each step indicates which bolts and/or screws you will need for assembly, as well as any flat washers, lock washers, t-nuts or lock nuts. A. This is the time for you to inventory all your hardware, wood and accessories, referencing the parts identification sheets. This will assist you with your assembly. • The wood pieces will ...

A: Lay 2 (0349) Rock Rails down, side by side with angled edges facing down. (fig. 2.1) B: Place (1779) CE Access Board on the bottom of each (0349) Rock Rail as shown in fig. 2.1. Make sure (1779) CE Access Board is flush to the outside and bottom edges of each (0349). Attach using 4 (S2) #8 x 1-1/2” Wood Screws. C: 7-3/4” down from the top of both (0349) Rock Rails place 1 (1777) CE Ro ...

Make sure triangle is tight against beam Warning: For your child’s safety, orientate the swing hangers as shown to ensure your swing will have proper swing motion when installed. Failure to do so could result in premature failure of the swing hanger or swing chain. A: In the middle holes of (1825) Back Beam install 2 Bolt-Thru Swing Hangers (fig. 3.1) making sure the swing hangers are oriented in the direction shown in ...

A: Attach 2 (1863) SW Posts to (1856) SW Upright using 2 (G4) 5/16 x 4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 4.1) B: Attach (1862) SW Support to both (1863) SW Posts and (1856) SW Upright using 3 (G5) 5/16 x 4-1/2” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 4.1) Wood Parts Hardware 2 x 5/16 x 4” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut) 3 x 5/16 x 4-1/2” ...

WARNING: Glider Hangers must be tight and secure to Swing Beams. A: Place (4919) SW Rail Block in the centre between (1826) Front Beam and (1825) Back Beam and attach with 1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, flat washer and t-nut). (fig. 5.1 & 5.2) B: Attach Swing End Assembly to the side of the Swing Beam Assembly with the overhang (fig. 5.3 & 5.4) using 1 (G5) 5/16 x 4-1/2” Hex Bolt (with ...