JVC FS-H35 Instructions Manual

Enter below the Model No. and Serial No. which are located either on the rear, bot- tom or side of the cabinet. Retain this information for future reference. Model No. Serial No. FS-H35— Consists of CA-FSH35 and SP-UXH35 FS-H30— Consists of CA-FSH30 and SP-UXH30 COMPACT COMPONENT SYSEM SYSTEME DE COMPOSANTS COMPACT INSTRUCTIONS MANUEL D’INSTRUCTIONS GVT0101-002C [C] COMPACT COMPONENT SYSTEM English Français COVER_FS-H30[C]fff.pm6 03.3.3, 2:26 PM 1 ...

Mises en garde, précautions et indications diverses CAUTION— (standby/on) button! Disconnect the mains plug to shut the power off completely (all lamps and indications go off). The (standby/on) button in any position does not disconnect the mains line. • When the unit is on standby, the STANDBY lamp lights red. • When the unit is turned on, the STANDBY lamp goes off. The power can be remote controlled. ATTENTION—Touche (attente/sous tension) Déconnectez la fiche secteur pour mettre l’appareil complètement hors tension (tous les témoins et toutes les indications s’éteignent). La touche (attente/so ...

This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For Canada/pour le Canada CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND. For Canada/pour le Canada THIS DIGITAL A ...

This manual is organized as follows: • The manual mainly explains operations using the buttons on the remote control. You can use the buttons both on the remote control and on the main unit for the same operations if they have the same or similar names (or marks), unless mentioned otherwise. • Basic and common information that is the same for many functions is grouped in one place, and is not repeated for each procedure. For instance, we do not repeat the information about turning on/off the unit, setting the volume, changing the sound effects, and others, which are explained in the section “Common Operati ...

Main Unit .......................................................................... 3 Remote Control ................................................................. 5 Getting Started............................................................. 6 Supplied Accessories ......................................................... 6 Connecting Antennas ........................................................ 6 Connecting Speakers ......................................................... 7 Connecting Other Equipment............................................ 8 Putti ...

STANDBY w q e r t Top view Front view TIMER/SNOOZE MULTI CONTROL ONE TOUCH REC AHB PRO VOLUME AUX TAPE CD TUNER BAND COMPACT DIGITAL AUDIO PHONES 4 ¢ 7 OPEN 9 7 p 1 2 5 6 8 4 3 Become familiar with the buttons on your unit. Main Unit Location of the Buttons EN01-13_FS-H30[C]f.pm6 03.2.5, 6:42 PM 3 ...

2 Disc cover 3 TIMER/SNOOZE button (10, 20 – 22) 4 ONE TOUCH REC (recording) button (18, 19) 5 (standby/on) button (11, 21) 6 Source buttons • AUX, @ # TAPE, BAND TUNER, and #/8 CD Pressing one of these buttons also turns on the unit. 7 MULTI CONTROL buttons • 4 (reverse skip), 7 (stop), and ¢ (forward skip) 8 AHB (Active Hyper Bass) PRO button (11) 9 0 OPEN (disc cover open) button (14) p VOLUME + / – buttons (11) q Display window w STANDBY lamp (11) e Cassette holder r Remote sensor t ) (cassette holder open) button (17 – 19) Display window 1 Tape operation indicators • 2 3 (tape direction), REC ( ...

1 Number buttons 2 BASS button (11) 3 Multi control buttons • UP, 4 (reverse skip), 7 (stop), ¢ (forward skip), and DOWN 4 SET button (13) 5 Source buttons • 3/8 CD, 2 3 TAPE, TUNER, and AUX Pressing one of these buttons also turns on the unit. 6 REV.MODE (reverse mode) button (17 – 19) 7 PRGM (program) button (15) 8 STANDBY/ON button (11, 21) 9 DISPLAY button (10) p CLOCK/TIMER button (10, 20, 21) q SLEEP button (22) w TREBLE button (11) e CANCEL button (16) r AUTO PRESET button (12) t FM MODE button (12) y REPEAT button (16) u RANDOM button (16) i AHB (Active Hyper Bass) PRO ...

The number in parentheses indicates the quantity of each piece supplied. • AM loop antenna (1) • FM antenna (1) • AC power cord (1) • Remote control (1) • Batteries (2) If anything is missing, consult your dealer immediately. Connecting Antennas FM antenna 1 Attach the FM antenna to the FM COAXIAL 75 Ω terminal. 2 Extend the FM antenna. 3 Fasten it up in the position which gives you the best reception, then fix it on the wall, etc. About the supplied FM antenna The FM antenna supplied with this unit can be used as temporary measure. If reception ...

AM LOOP terminals as illustrated. 2 Turn the AM loop antenna until you have the best reception. To connect an outdoor AM antenna When reception is poor, connect a single vinyl-covered wire to the AM EXT terminal and extend it horizontally. The AM loop antenna must remain connected. For better reception of both FM and AM • Make sure the antenna conductors do not touch any other terminals and connecting cords. • Keep the antennas away from metallic parts of the unit, connecting cords, and the power cord. AM antenna Vinyl-covered wire (not supplied) AM loop antenna (supplied) 1 2 Connecting Speakers 1 Pre ...

the top of the speaker grille, pull towards you. Then pull the bottom towards you. To attach the speaker grille, follow the illustration above. Connecting Other Equipment To connect an audio equipment You can connect audio equipment—used only as a playback device. • DO NOT connect any equipment while the power is on. • DO NOT plug in any equipment until all connections are complete. Be sure that the plugs of the audio cords are colored: White plugs and jacks are for left audio signals, and red ones for right audio signals. Holes Projections To remove the speaker grilles ...

Control Insert the batteries—R6(SUM-3)/AA(15F)—into the remote control, by matching the polarity (+ and –) on the batteries with the + and – markings on the battery compartment. When the remote control can no longer operate the unit, replace both batteries at the same time. • DO NOT use an old battery together with a new one. • DO NOT use different types of batteries together. • DO NOT expose batteries to heat or flame. • DO NOT leave the batteries in the battery compartment when you are not going to use the remote control for an extended period of time. Otherwise, the remote control will ...

Before operating the unit any further, first set the unit’s clock. When you plug in the power cord, the CLOCK indicator and “AM 12:00” start flashing on the display. You can set the clock whether the unit is on or off. • There is a time limit in doing the following steps. If the setting is canceled before you finish, start over from step 1. On the remote control: 1 Press CLOCK/TIMER. The hour digits start flashing on the display. 2 Press UP or DOWN to adjust the hour, then press CLOCK/TIMER. The minute digits start flashing. 3 Press UP or DOWN to adjust the minute, then press CLOCK/TIMER. On th ...

You can adjust the bass level (low frequency range) and the treble level (high frequency range) within a range of –5 to +5. When shipped, the bass level set to “BASS 0” and the treble level set to “TREBLE +1.” • This function only affects the playback sound, and does not affect your recording. • There is a time limit in doing the following steps. If the setting is canceled before you finish, start over from step 1. On the remote control ONLY: 1 Press BASS to adjust the bass level or press TREBLE to adjust the treble level. 2 Press UP to increase the level or press DOWN to decrease it. Reinforc ...

1 Press TUNER (or BAND TUNER on the unit) to select the band. The unit automatically turns on and tunes in to the previously received station—either FM or AM. • Each time you press the button, the band alternates between FM and AM. 2 Press and hold ¢ or 4 for more than 1 second. The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in. • If a program is broadcast in stereo, the STEREO indicator lights up. To stop searching, press ¢ or 4. When you press ¢ or 4 briefly and repeatedly The frequency changes step by step. To change the FM reception mode On the remote ...

You need to preset stations separately for the FM and AM bands. • There is a time limit in doing the following steps. If the setting is canceled before you finish, start over from step 2. On the remote control ONLY: 1 Tune in to the station you want to preset. • See “Tuning in to a Station” on page 12. 2 Press SET. 3 Press UP or DOWN to select a preset number. 4 Press SET again. The tuned station in step 1 is stored in the preset number selected in step 3. • Storing a new station on a used number erases the previously stored one. When you unplug the power cord or if a power failure ...

This unit has been designed to play back the following discs—CD, CD-R, and CD-RW. When playing a CD-R or CD-RW User-edited CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) can be played only if they are already “finalized.” • Usually you can play back your original CD-Rs or CD-RWs recorded in music CD format. However, sometimes they may not play depending on their characteristics or recording conditions. • Before playing CD-Rs or CD-RWs, read their instructions or cautions carefully. • Some CD-Rs or CD-RWs may not play on this unit because of their disc characteristics, damage or stain on them, or if the player ...

While playing a disc, you can do the following operations. To stop playing for a moment During play, press 3/8 CD. While pausing, the elapsed playing time flashes on the display. To resume playing, press 3/8 CD again. To go to another track Before or during play, press ¢ or 4 repeatedly. • ¢ : Skips to the beginning of the next or succeeding tracks. • 4 : Goes back to the beginning of the current or previous tracks. To go to another track directly using the number buttons On the remote control ONLY: Pressing the number button(s) before or during play allows you to start playing the track number you want. Ex.: For ...

• You cannot go back to the previous track by pressing 4. To stop playing, press 7. To exit from Random Play, press RANDOM before or after playing. Random Play is canceled and Normal Play resumes. • The RANDOM indicator goes off. Repeating Tracks—Repeat Play You can have all the tracks, the program or individual track currently playing, repeat as many times as you like. On the remote control ONLY: To repeat playing, press REPEAT before or during play. • Each time you press the button, Repeat Play changes as follows, and the following repeat indicator lights up on the display: : Repeats one track. ...

You can play back type I tapes. Playing Back a Tape 1 Press ) for cassette deck on the unit. The cassette holder opens. 2 Put a cassette in with the exposed part of the tape down. 3 Close the cassette holder cover gently. 4 Press 2 3 TAPE. The unit automatically turns on and the tape starts playing. The tape direction indicator (3 or 2) flashes slowly on the display. • Each time you press the button, the tape direction changes: 3 : plays the front side. 2 : plays the reverse side. When the tape plays to the end, the deck automatically stops if the Reverse Mode is set to or . (See “To play both sides—Reverse Mode.” ...