Whispbar K631W Fitting Instructions Manual

Text of Whispbar K631W Fitting Instructions Manual

Fitting Instructions for Basic Carrier

D Montageanleitung für Basisträgersystem ES Instrucciones de montaje para el sistema de transporte F Instructions de montage pour Basic Carrier NO Monteringsanvisning for takstativ PT Instruções de Montagem para sistema de transporte. RU Установочные Инструкции для Поперечных Балок x 1 x 4 x 4 x 4 x 4 x 1 x 4 Revision No: 2A 1

MAX kgs (lbs)

W/P WHD Land Rover Freelander 2 , 5dr SUV 07-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs) Freelander 2 , 5dr SUV 07-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs) Freelander 2 , 5dr SUV 07-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs) Freelander 2 , 5dr SUV 07-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs) LR2 , 5dr SUV 07-+ US 75 kgs (165 lbs) 75 kgs (165 lbs) 2

Whispbar K631W First Time Installation

G Remove parts from inside the package and check. Contact your dealer if any parts are missing or damaged. G These instructions show type A crossbar fitted. They also apply to type B, C and D. G This kit fits type A, B, C and D. G Use keys to remove covers. 3

Whispbar K631W G Use hex screwdriver to reverse adjusting

screw 10 turns. G Press adjusting screw and pull crossbar legs out. Refer to the crossbar instructions for crossbar adjustment method. G Ensure each end of the crossbar is adjusted equally. G Attaches to factory-fitted mounting points G Please check the rear of this manual for information relating specifically to your vehicle. G Adjust crossbar in or out to suit vehicle. Refer to the crossbar

G Remove plastic clamp block by gripping bar

leg with fingers and push firmly with thumbs until clamp block drops out behind leg. G Select plastic internal block (from fitting kit) and insert into foot. G Repeat for all legs. Fitment G Locate ditch mouldings on roof. G Carefully remove centre section of ditch mould with flat-head screwdriver. 5

G Pull ditch moulding back towards you.

G Remove centre section. G Remove as shown. G Locate vehicle's fixed points. 6

Whispbar K631W G Remove plastic bungs as shown.

G Rotate as shown. G Mark reference point with a pen onto removed section of ditch mould. G Mark reference point with a pen onto removed section of ditch mould. 7

G Mark as shown.

G Use drill bit supplied, to drill holes in marked positions. G Re-install ditch mould in roof channel. G Align holes. 8

G Select grubscrews and screw into the

vehicle's fixed points. G Do not over tighten. G Repeat for all four positions. G Place crossbars on pads ensuring the pads fit into the holes underneath the foot and the grubscrew pass through the hole in the foot. G Repeat for all four positions. G Tighten adjusting screw to 5 Nm (3.7 ft lb) hand tight. 9

G Tighten the plastic knob. The side with the

nut showing should be facing up. G Ensure the plastic knob is in the position shown when fully tightened. G Repeat for all legs. G Check crossbar is securely attached to the vehicle. G Use keys to fit and lock covers 10

Removal of crossbars

G Remove the products from the vehicle when not in use. Make sure all loose parts are stored safely. G Using the Hex Key and the capscrews, secure the ditch mould to the vehicle. CAUTION: Recheck all fasteners immediately after a load is applied to the crossbars. Regularly check screws are tight. 11

G Clean the car roof and surfaces of the

product that will be in contact with the car roof. G Follow the fitting instructions for fitting the product to your vehicle. Make sure all steps are carried out in order. G Set crossbars a minimum distance of 700mm (27 1/2") apart where no other distance is specified in the fitting instructions. This is especially important when carrying long loads. G Check unit is securely attached

G Check and replace worn out or defective

parts. G Keep the product clean and maintained. G Never drive into a car wash with the roof rack system fitted. G Lubricate locks and adjusting screws at regular intervals. G Remove the products from the vehicle when not in use. Make sure all loose parts are stored safely. G Yakima Products, Inc. 15025 SW Koll Pkwy. Beaverton, OR 97006-6056 USA www.whispbar.com www.whispbar.ca www.whispbar.eu w

G Komponenten aus der Verpackung

nehmen und überprüfen. Setzen Sie sich mit Ihrem Händler in Verbindung, sollten Teile fehlen oder beschädigt sein! G Dargestellt ist der Querträger des Typs A. Die Anweisungen gelten aber auch für die Typen B, C und D! G Dieses Kit ist für die Typen A, B, C und D. G Abdeckungen mit Schlüsseln abnehmen. 14

G Innensechskantschlüssel benutzen und

Stellschraube mit 10 Umdrehungen lösen. G Befestigungsschraube eindrücken und Querträgerschenkel ausziehen. Siehe Anweisungen für das Einstellen der Querträger! G Sicherstellen, dass beide Enden der Querträger gleich lang eingestellt sind (Maß 'x', s. Abb.). G Zur Montage an werksseitig vorgesehenen Montagepunkten G Im hinteren Teil dieser Bedienungsanleitung finden Sie Informationen spezi

G Klemmblock nach hinten drücken und so

entfernen. G Innenblock aus dem Montage-Kit in den Fuß einsetzen. G Montage bei allen Beinen wiederholen. Befestigung G lokalisieren Graben Leisten auf dem Dach. G Beseitigen sie vorsichtig den mittleren abschnitt Gummirille mit einem Flachkopfschraubenzieher. 16

G Ziehen Sie die Dachrillenleiste zu sich.

G Entfernen Sie den mittleren Abschnitt. G Entfernen, wie dargestellt. G Ermitteln Sie die Fixierungspunkte des Fahrzeugs. 17

Whispbar Automobile Accessories Owners Instructions: