Whispbar K447W Fitting Instructions Manual

Text of Whispbar K447W Fitting Instructions Manual

Whispbar K447W Fitting Instructions for Basic Carrier

D Montageanleitung für Basisträgersystem ES Instrucciones de montaje para el sistema de transporte. F Instructions de montage pour Basic Carrier NO Monteringsanvisning for takstativ PT Instruções de Montagem para sistema de transporte. RU Установочные Инструкции для Поперечных Балок x 1 x 1 x 6 x 4 x 2 x 6 x 2 x 6 x 4 x 6 Revision No: 4C 1

Whispbar K447W MAX kgs (lbs)

W/P WHD Volkswagen Caddy Maxi, 5dr Van 08-+ ZA 75 kgs (165 lbs) 100 kgs (220 lbs) Caddy Maxi, 5dr Van 08-+ EU 75 kgs (165 lbs) 100 kgs (220 lbs) Caddy Maxi, 5dr Van 08-+ NZ 75 kgs (165 lbs) 100 kgs (220 lbs) Caddy Maxi, 5dr Van 08-+ AU 75 kgs (165 lbs) 100 kgs (220 lbs) 2

Whispbar K447W First Time Installation

G Remove parts from inside the package and check. Contact your dealer if any parts are missing or damaged. G This kit fits type A, B, C and D. G These instructions show type A crossbar fitted. They also apply to type B, C and D. G Use keys to remove covers. 3

G Use hex screwdriver to reverse adjusting

screw 10 turns. G Press adjusting screw and pull crossbar legs out. Refer to the crossbar instructions for crossbar adjustment. G Ensure each end of the crossbar is adjusted equally. G Adjust crossbar in or out to suit vehicle. Refer to the crossbar instructions for crossbar adjustment. G Please check the rear of this manual for information relating specifically to your vehicle. 4

G Tighten adjusting screw to 5 Nm (3.7 ft lb).

G Remove plastic clamp block by gripping bar leg with fingers and push firmly with thumbs until clamp block drops out behind leg. G Select plastic internal block (from fitting kit) and insert into foot. G Repeat for all legs. 5

G Refer to the underside of the pad for the

part number. G It is important to put the pads in the correct position on the vehicle. G Letters refer to the pad part numbers and position. G Pad Part Number: A = 11-04-218 B = 11-04-220 G Fit rubber pads (supplied with fitting kit) to foot. Pad may vary in shape to that shown. G Make sure the pad fits into the holes underneath the foot. 6

G Remove fixed-point cover screws with 5mm

Hex Key. G Fit the adaptor (A) to grubscrew (B). G Use the following grubscrew lengths for each position: A = M6 x 35mm (1 3/8") B = M6 x 50mm (2") 7

G Screw adaptor with grubscrew assembly

into roof. Tighten firmly. G Repeat for all four positions. G Place crossbar foot over clamp. G Tighten the red plastic knob. G In the fully tightened position, the knobs should be parallel with the vehicle. G Repeat for all four positions. 8

G Check crossbar is securely attached to the

vehicle. G Use keys to fit and lock covers CAUTION: Recheck all fasteners immediately after a load is applied to the crossbars. Regularly check screws are tight. 9

G Clean the car roof and surfaces of the

product that will be in contact with the car roof. G Follow the fitting instructions for fitting the product to your vehicle. Make sure all steps are carried out in order. G Set crossbars a minimum distance of 700mm (27 1/2") apart where no other distance is specified in the fitting instructions. This is especially important when carrying long loads. G Check unit is securely attached whenever y

G Check and replace worn out or defective

parts. G Keep the product clean and maintained. G Never drive into a car wash with the roof rack system fitted. G Lubricate locks and adjusting screws at regular intervals. G Remove the products from the vehicle when not in use. Make sure all loose parts are stored safely. G Yakima Products, Inc. 15025 SW Koll Pkwy. Beaverton, OR 97006-6056 USA www.whispbar.com www.whispbar.ca www.whispbar.eu w

Whispbar K447W G Komponenten aus der Verpackung

nehmen und überprüfen. Setzen Sie sich mit Ihrem Händler in Verbindung, sollten Teile fehlen oder beschädigt sein! G Dieses Kit ist für die Typen A, B, C und D. G Dargestellt ist der Querträger des Typs A. Die Anweisungen gelten aber auch für die Typen B, C und D! G Abdeckungen mit Schlüsseln abnehmen. 12

G Innensechskantschlüssel benutzen und

Stellschraube mit 10 Umdrehungen lösen. G Befestigungsschraube eindrücken und Querträgerschenkel ausziehen. Siehe Anweisungen für das Einstellen der Querträger! G Sicherstellen, dass beide Enden der Querträger gleich lang eingestellt sind (Maß 'x', s. Abb.). G Querträger auf erforderliche Breite einstellen. Siehe dazu Montageanleitung für die Querträger. G Im hinteren Teil dieser Bedien

G Stellschraube mit 5 Nm / 3.7 ft lb anziehen.

G Klemmblock nach hinten drücken und so entfernen. G Innenblock aus dem Montage-Kit in den Fuß einsetzen. G Montage bei allen Beinen wiederholen. 14

G Die Teilenummer finden Sie auf der

Unterseite des Pads. G Es ist wichtig, die pad an der richtigen Position am Fahrzeug anzubringen. G Buchstaben beziehen sich auf die Pad- Teilenummern und Position. G Pad-Teilenummer: A = 11-04-218 B = 11-04-220 G Gummidichtung aus dem Montagekit auf das Fußteil stecken. G Achten Sie darauf, dass die Pads in die Öffnungen unter den Füßen passen. 15

G Fixpunkt Montage Abdeckschrauben mit

dem 5mm Innensechskantschlüssel entfernen. G Stecken Sie den Adapter (A) auf den Gewindestift (B). G Nutzen Sie die folgenden Gewindestift Längen für jede Position: A = M6 x 35mm B = M6 x 50mm 16

G Schrauben Sie den Adapter mit der

Gewindestiftgruppe in das Dach. Ziehen Sie sie fest an. G Dies an allen vier Punkten wiederholen. G Querträgerfuß über die Klammern stecken. G Rote Flügelmutter festziehen. G In der vollständig festgezogenen Position sollten die Knöpfe parallel zum Fahrzeug stehen. G Dies an allen vier Punkten wiederholen. 17

G Überprüfen ob die Querträger sicher am

Fahrzeug befestigt sind. G Abdeckungen aufsetzen und mit Schlüsseln verschließen (s. Abb.). ACHTUNG! Schrauben regelmäßig auf festen Sitz prüfen! 18

Whispbar Automobile Accessories Owners Instructions: