Whispbar K389W Fitting Instructions For Basic Carrier

Text of Whispbar K389W Fitting Instructions For Basic Carrier

Fitting Instructions for Basic Carrier

D Montageanleitung für Basisträgersystem ES Instrucciones de montaje para el sistema de transporte. F Instructions de montage pour Basic Carrier NO Monteringsanvisning for takstativ PT Instruções de Montagem para sistema de transporte. RU Установочные Инструкции для Поперечных Балок x 4 x 1 x 1 x 2 x 1 x 1 x 1 x 1 Revision No: 6C 1

MAX kgs (lbs)

W/P WHD Hyundai Accent , 4dr Sedan 06-Dec 11 US 50 kgs (110 lbs) 50 kgs (110 lbs) Accent , 4dr Sedan 06-Dec 11 ZA 50 kgs (110 lbs) 50 kgs (110 lbs) Accent , 4dr Sedan 06-Jan 11 EU 50 kgs (110 lbs) 50 kgs (110 lbs) Accent , 4dr Sedan May 06-Dec 11 AU 50 kgs (110 lbs) 50 kgs (110 lbs) Accent , 4dr Sedan May 06-Dec 11 NZ 50 kgs (110 lbs) 50 kgs (110 lbs) Toyota Avensis Verso, 5dr MPV 01-06 EU 60 kgs (132 lbs) 60 kgs (132 lbs) I

First Time Installation

G Remove parts from inside the package and check. Contact your dealer if any parts are missing or damaged. G This kit fits type A, B, C and D. G These instructions show type A crossbar fitted. They also apply to type B, C and D. NOTE: Clamp images in these instructions may not be representative of the clamps in this kit 3

G Use keys to remove covers.

G Use hex screwdriver to reverse adjusting screw 10 turns. G Press adjusting screw and pull crossbar legs out. Refer to the crossbar instructions for crossbar adjustment. G Ensure each end of the crossbar is adjusted equally. 4

Whispbar K389W G Remove locking screw.

G Apply protective strip as shown. Trim if required. G Hyundai Accent G Letters refer to the part numbers stamped on clamps. G Clamp Part Number: A = 525A B = 526A C = 527A G It is important to put the clamps in the correct position on the vehicle. 5

G Toyota Ipsum / Avensis Verso

G Letters refer to the part numbers stamped on clamps. G Clamp Part Number: A = 525A B = 526A C = 527A G It is important to put the clamps in the correct position on the vehicle. G Attach clamp to each leg. NOTE; clamps may have labels showing their positions on the vehicle (For example; "Front Right"). G Refit locking screw so that it goes through the hole in the clamp. Do not begin to tighten the locki

G Hyundai Accent

G Fit rubber pads (supplied with fitting kit) to foot. Pad may vary in shape to that shown. G Toyota Ipsum / Avensis Verso G Fit rubber pad (supplied with crossbar) to foot. G Refer to the underside of the pad for the part number. G It is important to put the pads in the correct position on the vehicle. G Hyundai Accent G Letters refer to the pad part numbers and position. G Pad Part Number: A = 11-04-265 B = 11-04-266

G Make sure the pad fits into the holes

underneath the foot. Fitment G Place crossbar on vehicle. Minimum recommended spacing between the bars is 700mm (27 1/2") (unless otherwise stated). G Please check the rear of this manual for information relating specifically to your vehicle. G Adjust the legs on the crossbar so that they are positioned equally from the ends of the crossbar, and the clamps engage firmly on the body work of the ve

G Adjust crossbar in or out to suit vehicle.

Refer to the crossbar instructions for crossbar adjustment. G Please check the rear of this manual for information relating specifically to your vehicle. G Tighten adjusting screw to 5 Nm (3.7 ft lb). G Tighten locking screw on both legs evenly. 9

G Check crossbar is securely attached to the

vehicle. G Use keys to fit and lock covers CAUTION: Recheck all fasteners immediately after a load is applied to the crossbars. Regularly check screws are tight. 10

Whispbar K389W G Clean the car roof and surfaces of the

product that will be in contact with the car roof. G Follow the fitting instructions for fitting the product to your vehicle. Make sure all steps are carried out in order. G Set crossbars a minimum distance of 700mm (27 1/2") apart where no other distance is specified in the fitting instructions. This is especially important when carrying long loads. G Check unit is securely attached

G Check and replace worn out or defective

parts. G Keep the product clean and maintained. G Never drive into a car wash with the roof rack system fitted. G Lubricate locks and adjusting screws at regular intervals. G Remove the products from the vehicle when not in use. Make sure all loose parts are stored safely. G Yakima Products, Inc. 15025 SW Koll Pkwy. Beaverton, OR 97006-6056 USA www.whispbar.com www.whispbar.ca www.whispbar.eu w

Whispbar K389W G Komponenten aus der Verpackung

nehmen und überprüfen. Setzen Sie sich mit Ihrem Händler in Verbindung, sollten Teile fehlen oder beschädigt sein! G Dieses Kit ist für die Typen A, B, C und D. G Dargestellt ist der Querträger des Typs A. Die Anweisungen gelten aber auch für die Typen B, C und D! BITTE BEACHTEN: die in dieser Anleitung gezeigten Klammerillustrationen können von den Klammern dieses Zubehörsatzes

G Abdeckungen mit Schlüsseln abnehmen.

G Innensechskantschlüssel benutzen und Stellschraube mit 10 Umdrehungen lösen. G Befestigungsschraube eindrücken und Querträgerschenkel ausziehen. Siehe Anweisungen für das Einstellen der Querträger! G Sicherstellen, dass beide Enden der Querträger gleich lang eingestellt sind (Maß 'x', s. Abb.). 14

G Stellschraube entfernen.

G Sicherheitsstreifen wie gezeigt anbringen. Wenn nötig, zurecht schneiden. G Hyundai Accent G Die Buchstaben beziehen sich auf die in die Klammern eingestanzten Teilenummern. G Klammer-Teilenummern: A = 525A B = 526A C = 527A G Es ist wichtig, die Klammern an der richtigen Position am Fahrzeug anzubringen. 15
G Toyota Ipsum / Avensis Verso G Die Buchstaben beziehen sich auf die in die Klammern eingestanzten Teilenummern. G Klammer-Teilenummern: A = 525A B = 526A C = 527A G Es ist wichtig, die Klammern an der richtigen Position am Fahrzeug anzubringen. G An jedem Fuß eine Klammer befestigen. ACHTUNG: Einige Klammern tragen Hinweise zur Montageposition (z.B. "vorne rechts"). G Stellschraube so wieder einsetzen, dass sie durch die Öffnung in
G Hyundai Accent G Gummidichtung aus dem Montagekit auf das Fußteil stecken. G Toyota Ipsum / Avensis Verso G Montieren Sie das Gummi-Pad (wird zusammen mit der Querstange geliefert) an dem Fuß. G Die Teilenummer finden Sie auf der Unterseite des Pads. G Es ist wichtig, die pad an der richtigen Position am Fahrzeug anzubringen. G Hyundai Accent G Buchstaben beziehen sich auf die Pad- Teilenummern und Position. G Pad-Teilenummer: A = 1

Whispbar K389W G Achten Sie darauf, dass die Pads in die

Öffnungen unter den Füßen passen. Befestigung G Setzen Sie den Querträger auf das Fahrzeug. Der empfohlene Mindestabstand zwischen den Trägern beträgt 700 mm (sofern nicht anders angegeben). G Im hinteren Teil dieser Bedienungsanleitung finden Sie Informationen speziell für Ihr Fahrzeug. G Füße am Querträger so einstellen, dass sie von den Enden der Querträger gleich weit entfernt und

Whispbar Automobile Accessories Owners Instructions: