Whispbar K088W Fitting Instructions Manual

Text of Whispbar K088W Fitting Instructions Manual

Whispbar K088W MAX kgs (lbs)

W/P WHD Hyundai Sonata , 4dr Sedan 94-97 ZA 50 kgs (110 lbs) 50 kgs (110 lbs) Sonata , 4dr Sedan 94-97 EU 50 kgs (110 lbs) 50 kgs (110 lbs) Sonata , 4dr Sedan Nov 93-May 96 NZ 50 kgs (110 lbs) 50 kgs (110 lbs) Sonata , 4dr Sedan Oct 93-Aug 96 AU 50 kgs (110 lbs) 50 kgs (110 lbs) Sonica , 4dr Sedan 94-97 EU 50 kgs (110 lbs) 50 kgs (110 lbs) 2

First Time Installation

G Remove parts from inside the package and check. Contact your dealer if any parts are missing or damaged. G This kit fits type A, B, C and D. G These instructions show type A crossbar fitted. They also apply to type B, C and D. NOTE: Clamp images in these instructions may not be representative of the clamps in this kit 3

G Use keys to remove covers.

G Use hex screwdriver to reverse adjusting screw 10 turns. G Press adjusting screw and pull crossbar legs out. Refer to the crossbar instructions for crossbar adjustment method. G Ensure each end of the crossbar is adjusted equally. 4

G Remove locking screw.

G Cut protective strip in four equal lengths. G Apply protective strip as shown. Trim if required. G Attach clamp to each leg. NOTE; clamps may have labels showing their positions on the vehicle (For example; "Front Right"). 5

G Refit locking screw so that it goes through

the hole in the clamp. Do not begin to tighten the locking screw. G Fit rubber pad (supplied with crossbar) to foot. G Make sure the pad fits into the holes underneath the foot. 6

G Place crossbar on vehicle. Minimum

recommended spacing between the bars is 700mm (27 1/2") (unless otherwise stated). G Clamps over body trim. G Adjust the legs on the crossbar so that they are positioned equally from the ends of the crossbar, and the clamps engage firmly on the body work of the vehicle. G Tighten adjusting screw to 5 Nm (3.7 ft lb) hand tight. 7

G Tighten locking screw on both legs evenly.

G Check crossbar is securely attached to the vehicle. G Use keys to fit and lock covers 8

CAUTION: Recheck all fasteners immediately after

a load is applied to the crossbars. Regularly check screws are tight. 9

Whispbar K088W G Clean the car roof and surfaces of the

product that will be in contact with the car roof. G Follow the fitting instructions for fitting the product to your vehicle. Make sure all steps are carried out in order. G Set crossbars a minimum distance of 700mm (27 1/2") apart where no other distance is specified in the fitting instructions. This is especially important when carrying long loads. G Check unit is securely attached

G Check and replace worn out or defective

parts. G Keep the product clean and maintained. G Never drive into a car wash with the roof rack system fitted. G Lubricate locks and adjusting screws at regular intervals. G Remove the products from the vehicle when not in use. Make sure all loose parts are stored safely. G Yakima Australia Pty Ltd 17 Hinkler Court Brendale QLD 4500 AUSTRALIA www.whispbar.com www.whispbar.com.au www.whispbar.c

WARRANTY & DISCLAIMER

Yakima Australia Pty Ltd ABN 58 154 440 221 17 Hinkler Court, Brendale QLD 4500 Tel: 0800 4776 722 (NZ) or 1800 143 548 (AU) Email: [email protected] or [email protected] Where the product is supplied to the customer for other than business purposes within the meaning of section 43 of the New Zealand Consumer Guarantees Act 1993, the provisions of that Act shall apply. It is important that anyone who fits

Alternately, you can write to Yakima at 17 Hinkler Court, Brendale QLD Australia 4500 in order to make a claim under your

warranty. Upon contacting Yakima directly, you should explain as fully as possible the defect. A Yakima representative will provide you with appropriate instructions for returning the product together with a copy of the original purchase invoice or receipt to Yakima. The costs and expenses associated with making a claim under your

Whispbar Automobile Accessories Owners Instructions: