Whispbar K046W Fitting Instructions Manual
Text of Whispbar K046W Fitting Instructions Manual
MAX kgs (lbs)
W/P
WHD
Renault
25 , 4dr Hatch 83-Sep 92
AU
50 kgs (110 lbs)
50 kgs (110 lbs)
25 , 4dr Sedan Nov 83-Mar 93
NZ
50 kgs (110 lbs)
50 kgs (110 lbs)
Holden
Apollo JK/JL, 4dr Sedan Aug 89-Mar 93
AU
50 kgs (110 lbs)
50 kgs (110 lbs)
Toyota
Camry , 4dr Sedan 87-91
US
50 kgs (110 lbs)
50 kgs (110 lbs)
Camry Ultima, 4dr Sedan Jul 86-Jan 90
NZ
50 kgs (110 lbs)
50 kgs (110 lbs)
Camry SV20/21, 4dr Sedan May 87-Jan 93
AU
50 kgs (110 lbs)
First Time Installation
G Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
G This kit fits type A, B, C and D.
G These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
G Use keys to remove covers.
G Use hex screwdriver to reverse adjusting
screw 10 turns.
G Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
G Ensure each end of the crossbar is
adjusted equally.
4
G Remove locking screw.
G Cut protective strip in four equal lengths.
G Apply protective strip as shown.
Trim if required.
G Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
5
G Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
G Fit rubber pad (supplied with crossbar) to
foot.
G Make sure the pad fits into the holes
underneath the foot.
6
G Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
G Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
G Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
7
Whispbar K046W G Tighten locking screw on both legs evenly.
G Check crossbar is securely attached to the
vehicle.
G Use keys to fit and lock covers
8
Whispbar K046W CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
9
Whispbar K046W G Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
G Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
G Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
G Check unit is securely attached
G Check and replace worn out or defective
parts.
G Keep the product clean and maintained.
G Never drive into a car wash with the roof
rack system fitted.
G Lubricate locks and adjusting screws at
regular intervals.
G Remove the products from the vehicle
when not in use. Make sure all loose parts
are stored safely.
G Yakima Australia Pty Ltd
17 Hinkler Court
Brendale QLD 4500
AUSTRALIA
www.whispbar.com
www.whispbar.com.au
www.whispbar.c
WARRANTY & DISCLAIMER
Yakima Australia Pty Ltd ABN 58 154 440 221
17 Hinkler Court, Brendale QLD 4500
Tel: 0800 4776 722 (NZ) or 1800 143 548 (AU)
Email: [email protected] or [email protected]
Where the product is supplied to the customer for other than business purposes within the meaning of section 43 of the New
Zealand Consumer Guarantees Act 1993, the provisions of that Act shall apply. It is important that anyone who fits
Alternately, you can write to Yakima at 17 Hinkler Court, Brendale QLD Australia 4500 in order to make a claim under your
warranty.
Upon contacting Yakima directly, you should explain as fully as possible the defect. A Yakima representative will provide you
with appropriate instructions for returning the product together with a copy of the original purchase invoice or receipt to
Yakima.
The costs and expenses associated with making a claim under your