Precor 9.31 Manual 

Text of Precor 9.31 Manual 

9.31, 9.33, 9.35 Treadmill

Page 1 9.31, 9.33, 9.35 Treadmill Warning: This service manual is for use by Precor trained service providers only. If you are not a Precor Trained Servicer, you must not attempt to service any Precor Product; Call your dealer for service. This document contains information required to perform the majority of troubleshooting, and replacement procedures required to repair and maintain this product. This document contains general p
9.31, 9.33, 9.35 Treadmill Page 2 Section One - Things you Should Know About This Appendix Section One, Things You Should Know. This section includes technical specifications. Read this section, as well as the 9.33 or 9.35 Treadmill Owner’s Manual, before you perform the maintenance procedures in this manual. Section Two, Software Features. Precor treadmills are programmed with several diagnostic and setup features. This section contains the procedures y
9.31, 9.33, 9.35 Treadmill Page 3 Procedure 2.1 - Accessing the Hardware Validation Program The treadmill's diagnostic program consists of the following modes: • Display Test • Keyboard Test • Heart Rate Test • Machine Test Procedure 1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker. 2. Refer to diagram 2.1 below and press keys RESET,5,1,7,6,5,7,6,1, sequentially. Use the numeric keypad to enter the nu
9.31, 9.33, 9.35 Treadmill Page 4 5. KEYBOARD TEST. 6. The keyboard test will place a dot on the display for each key on the display, including the numeric keypad. Pressing a key will cause the dot associated with the key to go out. Test all of the keys in this manner. Tug on the safety key lanyard, to ensure that the STOP key is activated. 7. Press and hold the OK or ENTER key to exit the keyboard test. 8. HEART RATE TEST. 9. The heart rate test will disp
9.31, 9.33, 9.35 Treadmill Page 5 Procedure 2.2 - Accessing the Information Display Program The information display will access the following data; • Odometer • Hour Meter • U Boot SW • U Base SW • Lower SW • Metrics Board SW • Usage log • Error log Procedure 1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker. 2. Refer to diagram 2.1 above and press keys RESET,6,5 sequentially. Use the numeric k
9.31, 9.33, 9.35 Treadmill Page 6 12. Press the OK or ENTER key to exit the U Boot SW display 13. U BASE SW 14. Press the OK or ENTER key. The U Base SW part number will be displayed. The U Base SW is the upper PCA operating system software. 15. Press the OK or ENTER key to exit the U Base SW display. 16. LOWER SW 17. Press the OK or ENTER key. The Lower SW part number will be displayed. The Lower SW is the lower PCA operating system software. 18. Press
9.31, 9.33, 9.35 Treadmill Page 7 31. Press the RESET key to exit the information display. 32. Note: the error log can also be entered at any time by pressing and holding the RESET key for four seconds.
9.31, 9.33, 9.35 Treadmill Page 8 Procedure 2.3 - Accessing the User Parameter Program This procedure allows you to change the following settings: • Select Units (9.31, 9.33) • Set Max Pause Time • Set Cool Down Time • Set Speed Limit Procedure 1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker. 2. Refer to diagram 2.1 above and press keys RESET,5,6,7,1 sequentially. Use the numeric keypad to enter the
9.31, 9.33, 9.35 Treadmill Page 9 16. SET SPEED LIMIT 17. Press the OK or ENTER key. 18. Use the ARROW keys to set the maximum speed between 1 and 12 MPH. 19. Press the ENTER key to select the currently displayed speed limit. 20. Press the RESET key to exit the set club parameters display.
9.31, 9.33, 9.35 Treadmill Page 10 Procedure 2.4 - Documenting Software Problems When a problem is found with the software in the upper or lower PCA, record the information listed below. When a problem occurs, record the following information: • Model and serial number • Software version number • Program number running when the problem occurred • A description of: a. What happened or failed to happen. b. The action taken by the user just before the
9.31, 9.33, 9.35 Treadmill Page 11 Section Three - Checking Treadmill Operation This section provides you with a quick method of checking treadmill operation. Check treadmill operation at the end of a maintenance procedure and when it is necessary to ensure that the treadmill is operating properly. Procedure 1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker. 2. Place the treadmill in Manual Mode. Adjust the sp
9.31, 9.33, 9.35 Treadmill Page 12 Procedure 4.1 - Calibrating the Lift Motor 1. Set the treadmill circuit breaker in the “off” position and unplug the line cord from the wall outlet. 2. Remove the motor cover. 3. Place the treadmill on it’s right side. Remove hitch and clevis pins that secure the lift tube to the lift platform. Diagram 4.1 - Lift Motor Mounting 1-1/16” Lift Tube Drive Screw
9.31, 9.33, 9.35 Treadmill Page 13 4. Plug the power cord into the wall outlet, set the treadmill circuit breaker in the “on” position. 5. Press keys RESET, 5,1,7,6,5,7,6,1, sequentially to enter the diagnostics routine. Refer to Procedure 2.1 and advance to the lift test. When the lift calibration number is displayed on the console, use the INCLINE � or INCLINE � key to set the lift calibration number to 38. CAUTION While running the lift motor in
9.31, 9.33, 9.35 Treadmill Page 14 Procedure 4.2 - Adjusting Drive Belt Tension 1. Set the treadmill circuit breaker in the “off” position and unplug the line cord from the wall outlet. 2. Remove the motor cover. 3. Place the drive belt tension gauge on the drive belt as shown in Diagram 4.2. Diagram 4.2 - Drive Belt Tension Gauge 4. The gauge should read approximately 75 inch/pounds. The drive belt tension is acceptable if it is in the range of 60 to
9.31, 9.33, 9.35 Treadmill Page 15 6. Re-install the motor cover. Diagram 4.3 - Drive Belt Adjustment 7. Plug the line cord into the wall outlet and set the treadmill circuit breaker in the “on” position. 8. Check treadmill operation per Section 3. Drive Motor Mounting Bolt
9.31, 9.33, 9.35 Treadmill Page 16 Procedure 4.3 - Treadmill Belt Cleaning Procedure: 1. First, check for proper operation of the safety stop key. Stand to one side of the treadmill. Insure that the stop key tether is hanging straight down from the stop key and is not wrapped around the handle bars. Push the “Quick Start” button and wait for the display to count down and for the running belt to begin moving. Once the running belt is moving pull the saf

Precor Treadmill Owners Instructions: