Edimax PS-3101P Quick Installation Manual
Text of the manual
55 // 88 //1166 PPoorrttss SSOOHHO
O
FFaasstt EEtthheerrnneett SSwwiittcchheess
Q
Quuiicckk IInnssttaallllaattiioonn G
Guuiiddee
English ..............…………...............……………... 2
Český ................................................................... 5
Deutsch ............................................................... 8
Español .............................................................. 11
Français .....................................
Front Panel & Connectors
Fast Ethernet Switch LED Panel
LED
Color
Status
Description
Lit
Power is supplied
PWR
(Power)
Green
Off
No power
Lit
A valid link is established
Flash
Data packets received
LNK/ACT
(Link/Activity)
Green
Off
No link is established
Lit
This port run at 100Mbps
SPEED
(10/100M)
Yellow
Off
This port run at 10Mbps
1. Operating Environment
This switching hub must be installed and operated within the
limits of specified operating temperature (32-131°F) and
humidity (10~95% Non-condensing).
z Do not place objects on top of the unit.
z Do not obstruct any vents at the sides of the unit.
z Do not position the unit near any heating source such
as heater, radiator, or dir
1. Power LED is not lit
z Check if the power cord is properly connected to the
external power adapter and the power outlet. Make sure
the DC power jack is firmly plugged into the power socket
of the switch.
2. Link/Activity is not lit when connect to 100Mbps device
z Check the power switch of the network device attached to
the switch; make
Čelní panel a konektory
Panel s diodami LED switche pro Fast Ethernet
Dioda LED
Barva
Stav
Popis
Svítí
Zařízení je napájeno
PWR
(Napájení)
Zelená
Nesvítí
Zařízení není napájeno
Svítí
Je vytvořeno platné
připojení
Bliká
Jsou přijímány datové
pakety
LNK/ACT
(Připojení/Aktivita)
Zelená
Nesvítí
Není vytvořeno platn
1. Provozní prostředí
Tento switch/hub musí být nainstalován a provozován v
prostředí, které splňuje limity, specifikované provozní teploty
(32-131°F) a vlhkosti (10-95% bez kondenzace).
z Na horní plochu zařízení nepokládejte žádné předměty.
z Nezakrývejte žádné výřezy po stranách zařízení.
z Neumisťujte toto zařízení
1. Dioda LED napájení (Power) nesvítí
z Zkontrolujte, zda je k externímu síťovému adaptéru a do
síťové zásuvky správně zapojen síťový napájecí kabel.
Prověřte, zda je konektor stejnosměrného napájení
zapojen do odpovídající zdířky na switchi.
2. Indikátor Link/Activity při připojení zařízení s
Vorderseite & Anschlüsse
Fast Ethernet Switch LED-Anzeige
LED
Farbe
Status
Beschreibung
Leuchtet
Es liegt Strom an
PWR
(Strom)
Grün
Aus
Kein Strom
Leuchtet
Eine gültige Verbindung
wurde hergestellt
Blinken
Datenpakete werden
empfangen
LNK/ACT
(Vervindung/Aktivität)
Grün
Aus
Keine Verbindung
hergestellt
Leuchtet
Dieser Port hat eine
Datenübe
Bei der Installation und beim Betrieb dieses Switching-Hubs
müssen die vorgeschriebenen Grenzen für
Betriebstemperatur (0-55 °C) und Luftfeuchte (10~95 %
keine Kondensation) eingehalten werden.
z Stellen Sie keine Gegenstände auf das Gerät.
z Blockieren Sie die Entlüftungsöffnungen an den Seiten
des Geräts nicht.
z Stellen Sie d