Siemens RUGGEDCOM WIN7225 Installation Manual

2 Device Management 3 Technical Specifications 4 Certification 5 ...

All rights reserved. Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or trademark registration. This document contains proprietary information, which is protected by copyrigh ...

iii Table of Contents Preface ............................................................................................................. v Alerts .................................................................................................................................................. v Related Documents ....................................................................................... ...

RUGGEDCOM WIN7225 Installation Guide iv 2.9.3  Applying Self-Amalgamating Tape ..................................................................................... 25 Chapter 3 Device Management ....................................................................................... 27 3.1  Connecting to the Base Station .................................................................................................... 27 3.2  Co ...

installation, commissioning and important technical specifications. It is intended for use by network technical support personnel who are responsible for the installation, commissioning and maintenance of the base station. It is also recommended for use by network and system planners, system p ...

Related Documents Other documents that may be of interest include: • RUGGEDCOM WIN User Guide [https://support.industry.siemens.com/cs/ww/en/view/109737450] • RUGGEDCOM WIN1210 Installation Guide [https://support.industry.siemens.com/cs/ww/en/view/109738768] • RUGGEDCOM WIN1212 Installation Guide [https:/ ...

• Ask questions or share knowledge with fellow Siemens customers and the support community ...

broadband wireless access systems based on the IEEE 802.16e mobile WiMAX standard. These systems are designed for robustness and simplicity, offering feature-rich services with low deployment and operation costs, for unmatched operator competitiveness and fast return on investment. The RUG ...

serial servers and WiMAX wireless network equipment. For more information, contact a Siemens Sales representative. CONTENTS • Section 1.1, “Feature Highlights” • Section 1.2, “Description” • Section 1.3, “Required Tools and Materials” • Section 1.4, � ...

interfacing with the device. 1 2 3 5 4 Figure 1: RUGGEDCOM WIN7225 1. ANT 2 Port    2. RS-232 Serial Console Port    3. DC/ETH Port    4. GPS Port    5. ANT 1 Port RS-232 Serial Console Port An RJ45 serial console port for interfacing di ...

Sprays • Cleaner and de-greaser • SCC3 conformal coating • Corrosion protection Mounting Hardware (Wall/Tower Only) • Four 8 mm (5/16 in) screws • Four 8 mm (5/16 in) flat washers • Four 8 mm (5/16 in) spring washers • Wall anchors (if necessary) Mounting Hardware (Pole Only) • Two steel band straps Section 1.4 Decommissioning and Disposal Proper dec ...

5 Installing the Base Station This chapter describes how to install the base station, including mounting the device, connecting power, and connecting the device to the network. DANGER! Electrocution hazard – risk of death or serious injury. When the base station is installed in an outdoor location, all indoor components (e.g. Ethernet and power supply) should be connected through ...

RUGGEDCOM WIN7225 Installation Guide 6 General Procedure IMPORTANT! Install equipment in accordance with the electrical code relevant to the country of installation, such as: • the National Electrical Code (NEC), ANSI/NFPA 70 • the Canadian Electrical Code (CEC), Part 1, CSA C22.1 • the National Electrical Safety Code IEEE C2 (when applicable) Unless marked or otherwise identified, the Standard for the Protection ...

Unpacking the Base Station 7 1. Review the relevant certification information for any regulatory requirements. For more information, refer to Section 5.1, “Approvals”. 2. Select an appropriate site and perform a site survey. For more information, refer to Section 2.3, “Site Preparation and Precautions”. 3. Unpack and inspect the base station components. For more informatio ...

RUGGEDCOM WIN7225 Installation Guide 8 Site Preparation and Precautions Section 2.3 Site Preparation and Precautions Before installing the base station and or antenna(s), it is important to plan the the complete installation and make sure the appropriate safe guards are in place. Site Selection Consider the following recommendations when selecting an appropriate site for the base station and antenna(s): • Mount the ...

Installing the Base Station in Hazardous Locations 9 • Always assume an overhead line can cause serious injury or death. Note that electric power lines and phone lines look alike. • Always wear the appropriate Personal Protective Equipment (PPE) for the task, including but not limited to rubber boots, rubber gloves, hard hat, harness and lanyard, etc. • Always use a ladder mad ...

RUGGEDCOM WIN7225 Installation Guide 10 Mounting the Base Station II 3 G nA IIC T4 X P/N: WiN72XX-Y Pico Base Station S/N: XXXXWWYYXXX WARNING - EXPLOSION HAZARD DO NOT SEPARATE WHILE CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE SAFE AVERTISSEMENT - RISQUE D'EXPLOSION NE PAS DÉBRANCHER TANT QUE LE CIRCUIT EST SOUS TENSION, À MOINS QU'IL NE S'AGISSE D'UN EMPLACEMENT NON DANGEREUX Rating: DC 48V, 1A Class I Division 2 Gr ...

Mounting the Base Station to a Pole 11 1. Liberally apply an anti-corrosion spray to all galvanized steel components, including mounting brackets, washers and screws. 2. Select a mounting location on the wall. 3. Align the mounting bracket with the selected mounting location on the wall/tower. 4. Mark the location of the mounting holes on the wall/tower. 5. Remove the mounting brack ...

RUGGEDCOM WIN7225 Installation Guide 12 Assembling the Base Station and Mounting Bracket 1. Attach the base station to the mounting bracket. For more information, refer to Section 2.5.3, “Assembling the Base Station and Mounting Bracket”. 2. Liberally apply an anti-corrosion spray to all galvanized steel components, including mounting brackets, nuts, washers and screws. 3. Thread two steel band straps through the ...