Shure AD4DUS-A Manual 

Text of Shure AD4DUS-A Manual 

AD4D Axient Digital Dual Receiver

The AD4D Axient Digital Dual Receiver sets a new standard in transparent digital audio and maximum spectral efficiency. Groundbreaking performance features include wide tuning, low latency, and High Density (HD) mode, en- suring solid performance in the most challenging RF environments. Networked control and signal routing options bring a new level of management and flexibility to your entire workflow. Compatible with all

Receiver Front Panel

AD4D Axient Digital Wireless Receiver POWER PUSH CONTROL NAVIGATE IR RF A B OL AUDIO SYNC 2 RX 2 RF A B OL AUDIO SYNC 1 RX 1 1 9 11 10 15 16 12 13 14 4 5 2 3 7 8 6 ENTER EXIT ① Headphone Volume Knob Controls headphone volume for the selected channel. Clip indicator warns of signal overload or limiter engagement. Press knob to access Dante options and headphone settings. ② Monitor Jack ¼" (6.3 mm) output jack. ③ Infrared

Shure AD4DUS-A ⑮ Control Wheel

• Push to enter a menu • Push to select a channel or menu item • Turn to scroll through menu items or to edit a parameter value ⑯ Power Switch Powers the unit on or off. Receiver Back Panel in thru word clock Term 75Ω output 2 line lift gnd -10 dB mic output 1 line lift gnd -10 dB mic AC Power ctrl 1 Dante 1 ctrl 2 Dante 2 PoE AES3 1&2 B A D C 12 V DC out 150mA cascade 1 9 10 13 11 3 2 5 8 7 6 4 12 ① AC Power Input IEC locking

Shure AD4DUS-A ⑪ Coaxial inputs from Antenna A and Antenna B

RF Connection for Antenna A and Antenna B. ⑫ RF Cascade Connectors C and D Passes the RF signal from Antenna A and Antenna B to one additional receiver. ⑬ Antenna Bias Indicator LED • Green: Antenna bias enabled • Red: Antenna fault • Off: Antenna bias disabled Menus and Configuration The receiver uses a two-tier menu structure to support multiple channels in a single rack space: • Device Configur

You can rotate the control wheel to choose different views of the information shown on the home screen, including channel name, group and channel, quality

meter, gain, and frequency. View 4 View 3 View 2 View 1 Screen Icons The following screen icons indicate receiver modes or settings: Standard Transmission Mode STD High Density Transmission Mode HD Frequency Group G: Channel C: TV band for selected frequency TV: AES3 Output Selected AES3 Selected Home Sc

Shure AD4DUS-A Access Control Enabled

Device Configuration Menu and Parameters Use the following menu items and parameter settings to configure the receiver at the device level. Tip: Use the ENTER button to save changes or press EXIT to cancel without saving. Device Configuration Menu Screen From the home screen, press the control wheel to access the Device Configuration menu. Device Configuration Menu Map Device RF Encryption RF Band Transmission Mode

Select the tuning band for the receiver.

Encryption Enables encryption of the RF signal. Transmission Mode Select Standard or High Density transmitter spacing. Custom Groups Configure, edit, or load custom frequency groups. Antenna Bias Enable antenna bias for active RF antennas. TV Format Adjust TV bandwidth to match regional standards. Device Audio AES3 Audio Configure AES3 audio parameters. Dante Names View, edit, and copy names for ne

Adjust the brightness of the display.

Invert Inverts the color of the display. Display Sleep Offers options to turn off display and front panel illumination after 10, 30, or 60 seconds. Tip: Press any front panel control to interrupt Display Sleep. Power Management (optional) DC Power Module Installed This menu item will only be shown if a DC power module has been installed in the receiver. Tx Firmware Update Align transmitter IR window

Channel Menu Map

Channel Name Transmitter Details IR Presets Radio Group Channel Frequency TV Find Next Find Best Channel Scan Start Group Scan Gain/Mute Switch Status Meter Overload Hold Audio Transmitter Slots Transmitters(s) Sync Unlink Frequency Diversity Advanced Tone Generator System Gain Interference Management Audio Gain Adjusts the receiver gain. Output Adjusts the output level of the receiver. Select Mute to turn off the receiver output. Meter Ov

Assign a frequency group.

C: (Channel) Assign a channel. Frequency Manually select a frequency. TV Displays the TV band for the selected frequency. Channel Name Channel Name Use the control wheel to assign or edit the channel name. Channel Scan Finds available channels within the selected group: • Find Next: Selects the nearest available channel • Find Best: Selects the channels with the best RF noise floor Group Scan Scans the selecte

Use IR Sync to form an audio channel between the transmitter and receiver.

Note: The receiver band must match the band of the transmitter. 1. Select a receiver channel. 2. Tune the channel to an available frequency using group scan. 3. Power on the transmitter. 4. Press the SYNC button on the receiver. 5. Align the IR windows until the receiver IR sync LED illuminates red. When complete, Sync Success! appears. The transmitter and receiver are now t

Assigning Transmitters to Transmitter Slots

Each receiver channel contains eight transmitter slots to control the RF signals passed by the receiver. Transmitters can be assigned to the channel slots or "registered" with the receiver. For added protection from interference, the receiver will issue a warning or block signals from any transmitters that aren't registered. To assign a transmitter to a receiver channel: 1. From the Channel menu: Transmitter(s)>T

All antenna ports provide a DC bias to power active antennas. Set the DC

power to off when using passive (non-powered) antennas. To turn off the antenna bias: 1. From the Device Configuration menu: Device RF>Antenna Bias 2. Press the control wheel to enable editing, and then select Off Tip: The Antenna Bias screen displays the current draw for each individual antenna and the total current draw for all antennas. RF Cascade Ports The receiver ha

LIMITER THRESHOLD: Adjusts the trigger point for the headphone limiter

to protect against unexpected increases in signal level • FD-S PRE/POST SELECTION: Selects a audio monitoring point in the signal path before or after Frequency Diversity processing for the head- phone. This setting is useful for isolating sources of noise or interference. System Gain The System Gain feature allows you to view and calculate all gain stages in the signal chain, inc

Use only one DHCP server per network

• All devices must share the same subnet mask • All receivers must have the same level of firmware revision installed • Look for the illuminated network icon on the front panel or display of each device: If the icon is not illuminated, check the cable connection and the LEDs on the network jack. If the LEDs are not on and the cable is plugged in, replace the cable and recheck the LEDs a

Note: When enabled, encryption is applied to all receiver channels. Encryption

does not affect Dante audio signals, audio quality, or channel spacing. 1. From the Device Configuration menu: Device RF>Encryption. 2. Use the control wheel to select On. 3. Press ENTER to save. 4. Perform an IR sync to complete the encryption between the transmitter and the receiver. The encryption key icon will appear on the display of both the receiver and the transmitter. N

Shure AD4DUS-A The transmitter and the receiver can be locked to prevent accidental or

unauthorized changes. A locked feature or button will produce the Locked screen on the LCD panel or the lock icon will flash on a transmitter. Encryption Mismatch Re-sync all receivers and transmitters after enabling or disabling encryption. Firmware Mismatch Paired transmitters and receivers must have the same firmware version in- stalled to ensure consistent operation

−98 dBm at 10-5 BER

Latency Analog Output 2.08 ms STD 2.96 ms HD Audio Frequency Response 20 – 20 kHz (±1 dB) AD1 Note: Dependent on microphone type AD2 Signal-to-Noise Ratio(Dynamic Range) typical, 20 Hz to 20 kHz, receiver gain setting = -12 dB Unweighted A-Weighted 117 dB 120 dB XLR Line Output 126 dB 130 dB Digital (AES3/Dante) Total Harmonic Distortion -6 dBFS, 1 kHz, System Gain @ +10 <0.01% System Audio Polarity Positive pressure

30 dB pad

Phantom Power Protection Yes Dimensions 44 x 483 x 333 mm H x W x D Weight 4.6 kg (10.1 lbs), without antennas Housing Steel; Extruded aluminum Power Requirements 100 to 240 V AC, 50-60 Hz, 0.55 A max. Thermal Power Dissipation 23 W (78 BTU/hr) Maximum 15 W (51 BTU/hr) Idle DC Power Requirements 10.5 to 32V DC4 A max. Network Interface 10/100 Mbps, 1Gbps, Dante Digital Audio Network Addressing Capability DHCP or Manual IP address

Shure Receiver Owners Instructions: