Shure BLX4R T11 Manual 

Text of Shure BLX4R T11 Manual 

©2014 Shure Incorporated

27A21196 (Rev. 5) Printed in U.S.A. BLX4R Wireless Microphone System Système de microphone sans fil BLX4R Drahtloses Mikrofonsystem BLX4R Sistema de micrófonos inalámbricos BLX4R Sistema radiomicrofonico BLX4R беспроводная микрофонная система BLX4R Draadloos microfoonsysteem BLX4R

CONSIGNES DE SÉCURITÉ IMPORTANTES

1. LIRE ces consignes. 2. CONSERVER ces consignes. 3. OBSERVER tous les avertissements. 4. SUIVRE toutes les consignes. 5. NE PAS utiliser cet appareil à proximité de l'eau. 6. NETTOYER UNIQUEMENT avec un chiffon sec. 7. NE PAS obstruer les ouvertures de ventilation. Laisser des distances suffisantes pour permettre une ventilation adéquate et effectuer l'installation en respectant les instructions du fabricant. 8. NE

ISTRUZIONI IMPORTANTI PER LA SICUREZZA

1. LEGGETE queste istruzioni. 2. CONSERVATELE. 3. OSSERVATE tutte le avvertenze. 4. SEGUITE tutte le istruzioni. 5. NON usate questo apparecchio vicino all'acqua. 6. PULITE l'apparecchio SOLO con un panno asciutto. 7. NON ostruite alcuna apertura per l'aria di raffreddamento. Consentite distanze sufficienti per un'adeguata ventilazione e installate l'apparecchio seguendo le istruzioni del costrut- tore. 8. NON insta

Conecte el receptor a la fuente de alimentación.

Conecte el receptor a la mezcladora o amplificador. Oprima el botón de alimentación para encender el receptor. Oprima el botón de grupo en el receptor para realizar un escaneo de grupo. Den E

Instale las baterías y encienda el transmisor.

En el transmisor, seleccione el grupo y canal para que coincidan con el receptor. Se deben iluminar las barras de RF y el LED de batería en el receptor. Die Batterien/Akkus einlegen und den Sender einschalten. Am Sender Gruppe und Kanal entsprechend der Empfängereinstellung einstellen. Auf dem Empfänger sollten di

Shure BLX4R T11 Si está configurando sistemas adicionales, deje encendidos el primer transmisor y receptor. Por cada receptor adicional, fije manualmente el

grupo para hacerlo coincidir con el primer receptor. Nota: El receptor automáticamente realizará un escaneo de canales para encontrar una frecuencia disponible después que se ha seleccionado el grupo. Fije la frecuencia del transmisor para que

④ channel Button

• Scan: push and release channel button to scan for an open channel • Manual: push and hold channel button to se- lect a channel. ⑤ Power Button Powers the receiver on/off. ⑥ Antenna Jack B BNC connector for antenna B. ⑦ DC Power Jack For

① LED Indicator

Displays power and battery status (see table). ② power Switch Toggles power on or off. ③ 4-Pin Microphone Input Jack (TA4 connector) ④ Antenna ⑤ group Button Changes group setting. ⑥ LED Display Displays group and channel setting. ⑦ channel Button Changes channel setting. ⑧ Battery Compartment ⑨ A

Single System Set Up

Before you begin, turn off all transmitters and turn on any equipment (other microphones or personal monitoring systems) that could cause interference during the performance. 1. Press and release the group button on the receiver. The receiver scans for the clearest group and channel. Note: If you want to stop the scan, push the group button again. 2. Turn on t

Multiple System Set Up

Up to 12 systems can operate simultaneously (band and RF environment dependent). Important: Set up each system one-at-a-time. Once a receiver and transmitter are tuned to the same group and channel, leave the transmitter powered on. Otherwise, scans from the other receivers will not detect that channel as occupied. Turn on any other equipment that could cause interference during the performance so it will be detected during the gr

Tips to Improve Wireless System Performance

If you encounter interference or dropouts, try the following suggestions: Getting Good Sound Adjusting Gain Monitor the audio meter on the receiver display when setting the transmitter gain. The OL indicator should only illuminate infrequently when you speak loudly or play your instrument loudly. BLX1 Rotate the audio gain a

Shure BLX4R T11 Expected life for AA batteries is up to 14 hours (total battery life varies depending upon battery

type and manufacturer). When the LED indicator turns red, it signifies "low battery" with approximately 60 minutes of re- maining battery life. For alkaline batteries only. For rechargeable batteries, solid red means the batteries are dead. To remove batteries from the handheld transmitter, push them out through the opening in the microphone batt

Shure BLX4R T11 NILES, IL 60714

BXL4R group channel (A-Y) (0-9) group channel (A-Y) (0-9) group channel (A-Y) (0-9) 14 Rack-Mounting a Receiver Use the supplied mounting hardware to install the receiver in a standard 19" audio equipment rack. Antenna Connection Diagram Troubleshooting Issue Indicator Status Solution No sound or faint sound Receiver RF bars and battery LED

Audio Input Level

gain position max -16 dBV maximum min (0 dB) +10 dBV maximum Gain Adjustment Range 26 dB Input Impedance 1 MΩ RF Transmitter Output 10 mW, typical varies by region Dimensions 110 mm X 64 mm X 21 mm H x W x D Weight 75 g (2.6 oz.), without batteries Housing Molded ABS Power Requirements 2 LR6 AA batteries, 1.5 V, alkaline Battery Life up to 14 hours (alkaline) BLX2 Audio Input Level gain position 0dB -20 dBV maxim

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Meets requirements of the following standards: EN 300 422 Parts 1 and 2, EN 301 489 Parts 1 and 9, EN60065. Meets essential requirements of the following European Directives: • R&TTE Directive 99/5/EC • WEEE Directive 2002/96/EC, as amended by 2008/34/EC • RoHS Directive 2002/95/EC, as am

① LED des piles de l'émetteur

• Vert = durée de fonctionnement supéri- eure à une heure • Rouge = durée de fonctionnement inféri- eure à une heure ② Écran LCD Affiche les paramètres du récepteur et de l'émetteur. ③ Bouton group • Balay

Shure Microphone system Owners Instructions: