Sharp R-342 Service Manual
Text of Sharp R-342 Service Manual
CHAPTER 1. SAFTY PRECAUTIONS
CHAPTER 2. CAUTIONS
CHAPTER 3. THE HEATING PRINCIPLE OF MICRO-
CHAPTER 4. INSTALLATIONS
CHAPTER 5. SCHEMATIC DIAGRAM
CHAPTER 6. CIRCUIT DESCRIPTION
CHAPTER 7. TOOLS AND MEASURING INSTRUMENTS
CHAPTER 8. MICROWAVE LEAAGE TEST
CHAPTER 9. MEASUREMENT OF MICROWAVE
CHAPTER 10. TROUBLE SHOOTING PROCEDURES
CHAPTER 11.
CHAPTER 12. IMPORTANT THINGS TO DO PRIOR
CHAPTER 13. SAFTY CHEC S AND TESTS AFTER
CHAPTER 14.
Parts List
MICROWAVE OVE
This device is to be serviced only by properly qualified service personnel.
Consult the service manual for proper service procedures to assure continued safety operation and for precautions to
be taken to avoid possible exposure to excessive microwave energy.
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
A) Do not operate or allow the oven to be operated with the door open
TABLE OF CONTENTS
(page)
SAFETY PRECAUTIONS---------------------------------------------------------Inside front cover
CAUTIONS------------------------------------------------------------------------------------------------1-1
THE HEATING PRINCIPLE OF MICROWAVE--------------------------------------------------2-1
INSTALLATIONS--------------------------------------------------------
• DO NOT operate on a 2-wire extension cord during
repair and use.
• NEVER TOUCH any oven components or wiring during
operation.
• BEFORE TOUCHING any parts of the oven, always
remove the power plug from the outlet.
• For about 30 seconds after the oven stops, an electric
charge remains in the high voltage capacitor. When
replacing or checking, you must discharge the high
voltage capacitor by shorting across the two terminals
with an insul
THE HEATING PRINCIPLE OF MICROWAVE
Microwave is one kind of radio wave whose wave length is very short, frequency is very high. Therefore, it is called ultrahigh
frequency electromagnetic wave. Microwave can heat food mainly result in the mutual affect of the food in the microwave field and
microwave field itself.
Under the affect of microwave field, the thermal effect mechanism produced from the mutual affect of the microwave and the food
includes two asp
1. Empty the microwave oven and clean inside it with
a soft, damp cloth. Check for damage such as
misaligned door, damage around the door or dents
inside the cavity or on the exterior.
2. Put the oven on a counter, table, or shelf that is
strong enough to hold the oven and the food and
utensils you put in it. (The control panel side of the
oven is the heavy side. Use care when handling.)
3. Do not block the vent and the air intake
As the door is closed, the contact of MONITOR
SWITCH opens. This switch creates the short circuit to
blow fuse during operation under abnormal condition.
(ie, should the contacts of primary and secondary
switch fail to open the circuit)
• The latches are secured by latch board. The oven light
turns on while the oven is in operation.
WHEN MICROWAVE POWER LEVEL
AND COOKING TIME SET
• The contacts of the timer switch changes to ON
posi
TOOLS AND MEASURING INSTRUMENTS
NECESSARY TOOLS
Tools normally used for TV servicing are sufficient.
Standard tools are listed below.
• Diagonal pliers
• Long nose pliers
• Phillips screwdriver
• Flat blade screwdriver
• Wrench (size 5mm)
• Nutdriver (size 5mm)
• Adjustable wrench
• Soldering iron
• Solder
• Vinyl insulation tape
• Polishing cloth
MICROWAVE LEAKAGE TEST
CAUTIONS
• Be sure to check microwave leaka
MEASUREMENT WITH OUTER CASE
REMOVED
• When you replace the magnetron, measure for
microwave energy leakage before the outer case is
installed and after all necessary components are
replaced or adjusted.
Special care should be taken in measuring the
following parts.
- Around the magnetron
-
The waveguide
MEASUREMENT WITH A FULLY
ASSEMBLED OVEN
• After all components, including the outer case, are fully
assembled, measure for microwave energy leakage
aro
MEASUREMENT OF MICROWAVE POWER OUTPUT
• Microwave power output measurement is made with
the microwave oven supplied at its rated voltage and
operated at its maximum microwave power setting with
a load of (1000±5) g of potable water.
• The water is contained in a cylindrical borosilicate glass
vessel having a maximum material thickness of 3 mm
and an outside diameter of approximately 190mm.
• The oven and the empty vessel are at ambient
temperature p
TROUBLE SHOOTING PROCEDURES
Before overhauling a microwave oven, you should judge the breakdown and the cause correctly, then you can repair it with
corresponding ways. The overhauling must be proceed in order, any hasty conclusion is not recommendable, otherwise
overworking would be done when repair. The microwave oven may occur compound breakdown due to all kinds of different
reasons, thus, when overhaul, they all should be taken into consideration. Spec
Examine when the oven at operating, but the food can’t be heated
Pull out the power plug, take off the outer case, discharge the capacitor, measure the resistance value of the primary winding and
the secondary winding of the transformer with a multi meter (FIG.5-3 and FIG.5-4). The resistance value of the primary winding
should be about 2.2 ohm, the secondary winding should be about 130 ohm, otherwise, it indicates the transformer has broken,
and shou
Ⅲ.REPAIRING METHOD OF SEVERAL BREAKDOWN
1.
Repair when there occurred large amounts microwave leakage. There are many factors, which may cause microwave leaking.
Following mentioned may be the main cause of microwave leakage:
(1) The door deformed, the hinge loosed or damaged that caused the door can not close tightly.
(2) The door pressing cover or the embed piece damaged or come off.
(3) Obvious damage or uneven of the oven.
(4) There are filth between
Means of repair when the oven can heat, but the turntable glass can’t move
Firstly, check whether the turntable holder is placed correctly. If it is correct, then pull out the power plug and take down the
turntable combination, measure the resistance value of the turntable motor with Rx1k grade of a multi meter If it is open-
circuited, it indicates the turntable motor has broken, and should be replaced by a new, same model one. If the resistance
valu
MOTOR TEST PROCEDURE
COMPONENTS
TEST PROCEDURE
RESULTS
Fan Motor
(Wire leads removed)
Measure the resistance.
(Ohm-meter scale:R× 100)
Normal:Approx. 47Ω
Abnormal:∞ or Several Ω
Turntable Motor
(Wire leads removed)
Measure the resistance.
(Ohm-meter scale:R× 1000)
Normal:Approx. 3.2kΩ
Abnormal:∞ or Several Ω
NOTE:
� A MICROWAVE LEAKGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS
SERVICED FOR ANY REASON.
� MAKE SURE THE WIRE LEADS ARE
Sharp R-342 COMMON BREAKDOWN AND MEANS OF REPAIRING
PHENOMENON
CAUSE
REPAIRING MEANS
1.When
starting
the
oven, the lamp is not on,
the turntable tray can’t
rotate and the food can’t
be heated
1. fuse broken
2. The primary and secondary winding of the
transformer are short-circuited.
3. The earthing or the polarity of the capacitor is
punctured.
4. The pilot switch can’t cut off.
5. The interlock switch hasn’t closed.
6. The power plug and the socket are not in
Sharp R-342 IMPORTANT THINGS TO DO PRIOR TO CRITICAL PART
SERVICING
The following instructions are CRITICAL to the owner’s safety. Be sure to follow all the instructions. Contact the
manufacturer of distributor if you have any question.
1.1 If the oven is operative prior to servicing a Microwave Leakage Test (Microwave Emission Check) should be
performed prior to servicing the oven.
1.2 in the event that any microwave oven found to have microwave emission level
Sharp R-342 SAFETY CHECKS AND TESTS AFTER SERVING
Constructional Checks
If mechanical or electrical(electronic) parts have been replaced be sure to follow the following steps.
1.1
Check for correct wiring, adequate mechanical decrements of parts, and firm connectors.
1.2
Check for adequate grounding.
1.3
Check the following items before turning the oven ON.
1)
Proper door closing, seal/choke surfaces, and hinges.
2)
No outer case damage.
3)
Proper interlock and monito