Sharp SMD2470ASY Installation Manual
Text of Sharp SMD2470ASY Installation Manual
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES ANd dImENSIoNS
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated
clearances and dimensions on pages 2 - 5. See Figure 1 (for 24") or Figures 4 and 5 (for 30").
CLEARANCES ANd dImENSIoNS
• Dimensions that are shown in Figure 1 (for 24") or Figures
4 and 5 (for 30") must be used. Given dimensions provide
minimum clearance. Locate electrical outlet in the shaded
area in the upper left-hand corner of the cutout. See Figure 9.
• Contact surface must be solid and level. Pay special attention
to the floor on which the Microwave Drawer will sit. The
floor of the opening should be constructed
This drawing represents a typical standard cabinet. If installed in custom
cabinets with extended counter tops, take into account visibility and access
to controls. See Figure 3.
Move oven location downward for
extended countertops
Extended countertops
Figure 3
A. 25"
B. 1/2" minimum
C. 15-7/8"
D. 36"
E. Control panel shown in open position
F. 24"
G. 34-1/2"
Figures 4, 5 and 6 contain many Microwave Drawer measurements
for reference when planning the drawer’s location.
This Microwave Drawer can be installed below any electric or
gas wall oven.
30" mICRoWAvE dRAWER mEASUREmENtS
A
B
C
D
E
F
G
H
I
J
K
L
M
M
N
O
P
Q
R
Figure 4
A. 84" wall cabinet
B. Optional wall oven cutout illustrated in sketch
C. Suggested electrical outlet location*
D. 6"
E. Anti-Tip block
F. 3-1/2"
G. 5"
H. 4"
I. 2" minimum
J. 28-7/16" op
B. Suggested electrical outlet location*
C. Anti-Tip block
D. 5"
E. 3-1/2"
F. 4"
G. 28-7/16" opening
H. 14-13/16" to bottom of Anti-Tip block
I. Allow 23/32" overlap
J. 23-1/2" minimum depth
K. Allow 3/16" overlap
L. 36" countertop height
M. Allow 7/16" overlap
N. Floor must support 100 lb
O. 30" cabinet minimum
P. 15-9/16" opening
Q. Allow 1/8" overlap
A. 21-5/8"
B. 4-11/1
This drawing represents a typical standard cabinet. If installed in custom cabinets with extended counter tops, take into account visibility and access
to controls. See Figure 7.
Move oven location downward for
extended countertops
Extended countertops
Figure 7
A. 25"
B. 1/2" minimum
C. 15-7/8"
D. 36"
E. Control panel shown in open position
F. 24"
G. 34-1/2"
Sharp SMD2470ASY NORMAL INSTALLATION STEPS
ANTI-TIP BLOCK INSTALLATION INSTRuCTIONS
To reduce the risk of tipping of the drawer, the Anti-Tip block must be properly installed
located 14 13/16-inches above the floor on which the Microwave Drawer will sit. The
6-inch Anti-Tip block must be provided by the installer. See Figures 1, 4 and 5. The
Anti-Tip block prevents serious injury that might result from spilled hot liquids.
If the Microwave Drawer is ever moved to a diffe
1. Place the drawer adjacent to the wall or cabinet opening.
Plug the power supply cord into the electrical outlet.
2. Carefully guide the drawer into the prepared opening.
Avoid pinching the cord between the oven and the wall.
3. Slide the drawer all the way until the mounting flange is
flush with the face of the cabinet. See Figure 10A.
4. Open the drawer. Using the 4 holes on the drawer as a
template, pre drill the cabinet using a 1/16" bit. See