Total TS730301 Manual 

instructions may result in electric shock, fire, and/or serious injury. This manual must accompany the equipment at all times and must be kept in a safe place to be available. Note: Save all warnings and instructions for future reference. Due to our ongoing R&D&I program, the specifications in this document are subject to change without notice. 1 ...

tool that cannot be controlled with the switch is dangerous and must be repaired. c. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool to avoid accidental starting of the tool. d. Use the power tool, accessories and bits etc. in accordance with these instructions, taking into account the working conditions and the work ...

have read and understand the following rules. • Read and become familiar with this entire instruction manual. • Learn about the tool's applications, limitations, and possible dangers. • Avoid dangerous conditions. Do not use power tools in wet or damp areas, and do not expose them to rain. • Keep work areas well lit. • Install the dust extraction unit. ...

proper hearing protection, such as safety ear muffs or safety ear plugs. This will reduce noise levels when using the band saw. Additional safety instructions for the band saw • To avoid injury from unexpected movement, make sure the saw is on a firm, level surface and is properly secured to prevent it from rocking. Make sure there is enough space for operations. ...

terminal. • Consult an electrician or service person if you do not fully understand the grounding instructions, or if you are not sure if the tool is properly grounded. Caution Always check that the outlet in question is properly grounded. If you are not sure, have a licensed electrician check the outlet. Make sure your extension cord is in good condition. Protect your extensi ...

80mm (3-1/8”) max. cutting width 230mm (9”) Product description 1. Saw blade tension screw 2. Saw blade tension lever 3. Track screw 4. Blade guide locking screw 5. Screw to adjust table inclination 6. Table tilt lock lever 7. Dust extraction nozzle 8. Rubber feet 9. Additional support 10. Front leaf guide screw 11. Variable guide 12. Work table 13. On/off switch 14 ...

18. Transmission belt 19. Lower wheel 20. Door 21. Upper wheel 22. Engine 23. Saw blade peephole Caveat This band saw is designed for indoor use only. Do not expose it to rain or use it in damp places. Assembly and operation Unpacked Carefully unpack the band saw and all its parts and compare them to the list. Do not dispose of the box or any other packaging until the band saw is fully assembled and you are sure it is working properly ...

L Table tilt lock lever M Hex keys 3, 4, 5mm N round head screws Mounting Caveat Before assembling the band saw, remove the safety key and unplug the power cord from the electrical outlet. The power cord must remain unplugged whenever you are working on your band saw. Rubber feet assembly (FIG.1) Before cutting, mount the four rubber feet to the four corner holes of the base with bolts (M6*30), large flat washers 6 a ...

• Attach the front blade guard and retighten the front blade guide screw. • Secure the table in position with the adjusting screw (5) and the table tilt lock lever (6). • Using a combination square, set the table perpendicular to the blade. Adjust the table tilt lock lever if necessary. • Set angular guide pointer to 00. • Insert and tighten the bolt and wing nut into the hol ...

Connect a dust collection system (FIG.8) The band saw includes a dust extraction nozzle that is located on the motor side of the band saw. This port can be connected directly to a dust collection system by connecting the collection end of the dust collection hose to the dust extraction nozzle. Instructions for use Caution Always keep in mind the following safety precautions: • Make sure the blade guides an ...

Wear leather gloves when handling band saw blades. Do not wear gloves when using the saw. • Turn the blade tension lever on the back of the tool clockwise until it locks into position to release blade tension (see Figure 9). • Release two latches on the side of the tool and open the top and bottom doors. Note: When opening the doors, make sure the latches are comple ...

Upper Blade Guides (Fig. 10-11) • Upper blade guides employ guide pins for side support and a ball bearing for rear support. • Loosen the screws and adjust the guide pins on the sides of the blade (see Figure 10). Use a feeler gauge to check that the guide pins are within 0.002” of the blade. • Lock adjustment by tightening screw. • Adjust the bearing at t ...

blade has more stiffness and stronger teeth. • A thick, narrow blade is used to cut curves, while a thin, wide blade is used to make long, straight cuts. blade pitch • The pitch describes the number of teeth per inch or the size of the tooth. A blade with more teeth per inch produces a smoother cut. • The type of material being cut determines the numb ...

• Lock the table in position by tightening the lock handle. Miter gauge (Fig.13) Use an angle fence to secure and hold the workpiece at the desired angle to prevent angled cuts. Use the scale to adjust the gauge to the desired angle. Caveat Never use the angle fence and the rip fence at the same time. The blade could get stuck in the work piece. The operator could be injured and/or ...

threaded or sliding surfaces. • Occasionally apply a coat of paste wax suitable for this type of tool to the worktable to keep it slippery and free of corrosion. Problem solving Attention Many accidents occur particularly in connection with problems and failures. So please note: 1. Always unplug before performing maintenance. 2. Check that all safety devices are operational ag ...

(Typical when cutting slippery or soft material) Use a blade with coarser teeth Excessive dirt and chips Clean thoroughly The saw does not start loose electrical connections Have a qualified electrician check the electrical connections Environment • Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. • Contact your local authority for information on a ...