Total TS42142101 Manual 

operation instructions within this manual. All those people who use and repair the machine must be familiar with the manual and informed of occupational hazards. Children and untrained persons may not use the miter saw. Also, those children should be out of the work area. It is also essential to observe the accident prevention regulations and apply them in the area where the equipment is to be used. The same applies to occupational health and safety regulations and rules. Caution Whenever you use a power tool, follow safety precautions to reduce ...

machine: 1. Keep work area organized and free of debris. 2. Consider the workplace where you use the machine. Do not use this electric machine in wet or damp areas. Do not use the machine in the presence of flammable gases or liquids. 3. Keep the work area lighted. 4. Keep people away from the work area. Do not allow people around you to come into contact with the machine or its power cord. 5. Store the machine carefully. When not in use, it should be well stored and out of the reach of children. 6. Do not overload the machine. It will be more efficient if you ...

Warning Before connecting the machine to a power source or outlet, make sure that the voltage supply is the same as that specified on the machine's nameplate. A power supply with a voltage higher than that specified for the machine can cause serious injury to both personnel and the machine. In case of doubt, do not plug in the machine and consult a specialist. On the other hand, a power supply with a voltage lower than that specified is detrimental to the motor of the machine. Note: Your machine is double insulated to provide additional protection against a possible electrical insulation failure within the tool. Always remo ...

Wear eye protection Wear respiratory protection Double insulated for extra protection Compliant with relevant safety standards - Do not block the cutting protection of the machine. Allow free movement to prevent blade from being exposed. - Wear a dust mask when using the machine. Don't forget to connect a dust collector to the machine and make sure it works properly. Be aware of injuries that can be caused by exposure to dust. Pay attention to the type of material to be cut, the extractor/vacuum used and the adjustment of the components (deflectors/protectors). - Handle and transport the blades always stored in a case. - Use the cor ...

2. Shaft 3. Work handle 4. Top fixed blade guard 5. Rotating blade guard 6. Shield Retraction Arm 7. Bevel lock 8. Bevel scale 9. 45° bevel adjustment screw 10. 0° bevel adjustment screw 11. Depth stop 12. Miter table 13. Miter scale 14. Cut slot 15. Miter lock 16. Trigger switch 17. Security lock 18. Spindle lock button 19. Blade bolt cover 20. 6mm hex key 21. Dust extraction port 22. Dust extraction port cover Assembly and operation Unpacked If you find any part of the machine in poor condition, do not operate it until the parts have been replaced or the fault has been fixed. Failure to do so could lead to serious inj ...

Transport Raise the miter saw only when the saw arm is locked in the down position, the machine is turned off, and the plug is unplugged. Lift the saw only by the handle (3) or the outer protection covers. Mounting The base of the saw has holes in each corner to facilitate bench mounting (fig. B). 1. Place the miter saw on a level horizontal bench or work table using bolts (not included) and attach the saw to the bench using 4 bolts. 2. If desired, the machine can be mounted to a piece of 13mm or thicker plywood which can then be clamped to your work support or moved to other job s ...

The miter table locks (15) are used to lock the table at the desired miter angle (fig. D). The miter saw cuts from 0° to 45° both left and right. To adjust the miter angle, loosen the miter table locks and rotate the miter table to the desired position. The miter table features positive click stops at 0°, 15°, 22.5°, 30° and 45° for quick adjustment of common miter angles. Warning Be sure to tighten the miter table locks before making a cut. Failure to do so could cause the table to move during the cut and cause serious personal injury. Bevel lock The bevel lock (7) is used to position the blade at the desired bevel angle (fig. ...

The rotating lower blade guard (5) protects both sides of the blade (fig. G). It retracts onto the upper blade guard (4) when the saw is lowered into the work piece. On and off 1. To turn on the machine, press and hold the on/off trigger switch (16) (fig. H). 2. To turn off the saw, release the On/Off Trigger Switch (16). Square the table with the blade 1. Make sure the electrical plug is disconnected from the outlet. 2. Push the saw arm (1) down to its lowest position and engage the spindle (2) to hold the saw arm in the transport position. 3. Loosen the miter locks (15). 4. Rotate the table (12) until the pointer is positio ...

various points. 9. The edge of the square and the saw blade must be parallel. 10. If the saw blade runs off square, adjust as follows. 11. Use an 8mm wrench or adjustable wrench to loosen the jam nut that holds the 0° bevel adjustment screw (10). Also, loosen the bevel lock (7) (fig. K). 12. Adjust the 0° bevel adjustment screw (10) with a 4mm hex key to align the blade with the square (fig. L). 13. Loosen the Phillips head screw holding the bevel scale pointer (8) and adjust the position of the pointer so that it accurately indicates zero on the scale. Retighten the s ...

1. Make sure the machine is unplugged. 2. Push the saw arm (1) down to its lowest position and engage the spindle (2) to hold the saw arm in the transport position. 3. Loosen the miter locks (15). 4. Rotate the table (12) until the pointer is positioned at 0º. 5. Tighten the miter locks (15). 6. Using a 5mm hex wrench, loosen the two screws that hold the depth stop (11) to the base (fig. N). 7. Place a square against the guide or depth stop (11) and next to the blade (fig. O). 8. Adjust the fence (11) until it is square with the blade. 9. Tighten the screws that hold the guide (11). 10. Loosen the Phillips head sc ...

Attention Never try to use a blade larger than the rated capacity of the saw. It could come into contact with the blade guards. Never use a blade that is too thick to allow the outer blade washer to engage with the flats on the shaft. That will not let the blade screw properly secure the blade on the shaft. Do not use the saw to cut metal or masonry. Make sure any arbor spacers and rings that may be required fit the arbor and mounted blade. 1. Make sure the electrical plug is disconnected from the outlet. 2. Press down on the work handle (3) and pull on the shaft (2) to disengage the saw arm (1). 3. Raise the saw arm (1) to its highest p ...

10. Clean the inner blade washer and the outer blade washer where they contact the blade with a drop of oil. 11. Fit the new blade onto the shaft taking care that the inner blade washer is behind the blade (fig. W). Caution To ensure proper blade rotation, always install the blade with the blade teeth and the printed arrow on the side of the blade pointing down. The direction of blade rotation is also marked with an arrow on the upper blade guard. 12. Replace outer blade washer. 13. Depress shaft lock button (26) and replace flat washer and blade bolt. 14. Use the 6mm hex key to tighten ...

Cross-section A cross cut is made by cutting along the grain of the workpiece. A 90º cross cut is made with the miter table at 0º. Miter crosscuts are made with the table set at a non-zero angle (fig. X). 1. Pull the shaft (2) and raise the saw arm (1) to its maximum height. 2. Loosen the miter locks (15). 3. Rotate the miter table (12) until the pointer lines up with the desired angle. 4. Retighten the miter locks (15) (fig. Y). Warning Be sure to tighten the miter locks before making a cut. Failure to do so could cause the table to move during the cut and cause serious personal injury. 5. Lay the workpiece flat on the table with one ...

workpiece. 10. Release the switch trigger (16) and allow the saw blade to stop rotating before removing the blade from the workpiece. Wait until the blade stops before removing the work piece. Bevel cut A bevel cut is made by cutting along the grain of the workpiece with the blade angled toward the fence and miter table. The miter table is set to the zero degree position and the blade is set at an angle between 0º and 45º (fig. Z). 1. Pull the shaft (2) and raise the saw arm to its maximum height. 2. Loosen the miter locks (15). 3. Rotate the miter table (12) until the po ...

good material (fig. a). 1. Pull the shaft (2) and raise the saw arm to its maximum height. 2. Loosen the miter locks (15). 3. Rotate the miter table (12) until the pointer lines up with the desired angle on the miter scale (13). 4. Retighten the miter locks (15). Warning Be sure to tighten the miter lock before making a cut. Failure to do so could cause the table to move during the cut and cause serious personal injury. 5. Loosen the bevel lock (7) and move the saw arm (1) to the left to the desired bevel angle (between 0º and 45º). Tighten the bevel lock (7). 6. ...

2. Remove dust and dirt regularly. Cleaning is best done with a soft brush or cloth. 3. Relubricate all moving parts at regular intervals. 4. Never use caustic agents to clean plastic parts. Caution Do not use cleaning agents to clean the plastic parts of the saw. A mild detergent on a damp cloth is recommended. General inspection Periodically check that all fixing screws are tight. They can vibrate loose over time. Environmental Protection Recycle unwanted materials instead of disposing of them as waste. All tools, hoses and packaging must be sorted, taken to the local r ...