Veranda 2127099 Manual
Text of Veranda 2127099 Manual
IMPORTANT, RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
7PC COUNTER HEIGHT FIRE DINING SET
ITM. / ART. 2127099
m# FG-VGO7FHDS
Customer Service
E-Mail : [email protected]
8:30a.m.– 5:00p.m. EST, M-F
Toll Free 1-855-390-5474 (English/Spanish)
(Int.) 001-855-286-4931 (English/Spanish)
Fax: (973) 428-8026
Website: www.foremostgroups.com
906 Murray Road East Hanover, New Jersey 07936 US
1
THIS ITEM IS INTENDED FOR OUTDOOR DOMESTIC USE ONLY, NOT FOR COMMERCIAL USE.
Please read instructions carefully and thoroughly before assembling. Check parts against
the parts list to make sure you have all the parts needed for proper assembly. Familiarize yourself
with the inventory of parts and the accompanying illustrations to ensure safe and proper assembly.
PARTS LIST
Failure to tighten bolts may cause injury. Do not force components and ove
Bolt (5/16” x 30mm)
BB
Flat Washer (φ8.5)
CC
Lock Washer (φ8.5)
DD
EE
Bolt (1/4” x 25mm)
FF
Bolt (1/4” x 30mm)
GG
Flat Washer (φ6.5)
HH
Lock Washer (φ6.5)
II
Wrench
JJ
KK
Natural gas orifice
Nut (5/16”)
Allen Wrench
PARTS LIST
6 PCS
6 PCS
24 PCS
24 PCS
48 PCS
24 PCS
6 PCS
2 PCS
M
Chair Bucket
N
Base
O
Bolt (5/16” x 35mm)
P
Q
R
S
Flat Washer (φ8.5)
T
Lock Washer (φ8.5)
Se
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference
WARNING: For Outdoor Use Only.
DANGER
FIRE OR EXPLOSION HAZARD
WARNING
Do not store or use gasoline, or other
flammable vapors and liquids,in the
vicinity of this or any other appli-
ance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
Installation and service must be per-
formed by a qualified install
IMPORTANT SAFETY INFORMATION
The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1●NFPA 54; National Fuel Gas Code; Natural Gas and Propane Installation Code, CSA B149.1;
or Propane Storage and Handling Code, CSA B149.2, as applicable.
The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve
during any pressure testing of the
IMPORTANT SAFETY INFORMATION ABOUT
PROPANE (LP) GAS
1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the U.S.
Deparment of Transportation (D.O.T.) Specifications for LP-Gas Cylinders, or the Standard for Cylinders,
Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339, as applicable.
2. The LP-gas supply cylinder to be used must have a listed overfilling prevention device (See
NOTE: Tool Required for Assembly: phillips screw driver ( NOT included)
Hardware Used:
EE
Bolt (1/4” x 25mm)
4
GG Flat Washer (φ6.5)
x
x
4
HH LockWasher (φ6.5) x 4
Figure 2
Remove all protective material carefully. Avoid cutting the surface of the furniture while removing the packaging material
on all components.
Loosely attach Back Panel (F) to the Left Side Panel (D) and the Right Side Panel (E) by bolts (EE) through
FF Bolt (1/4” x 30mm)
GG Flat Washer (φ6.5)
x
x
4
4
HH
Lock Washer (φ6.5) x 4
Loosely attach Gas Tank Support (H) to the Left Side Panel (D) and Right Side Panel (E) by bolts (FF) through lock
washers (HH), flat washers (GG), using Allen wrench (JJ). See figure 4.
DO NOT TIGHTEN BOLTS AT THIS POINTS.
JJ Allen Wrench
x 1
5.
Loosely attach Gas Tank Support (H) to the Gas Tank Baffle (I) by bolts (FF) through lock washer
Loosely attach Door (G) to the Right Side Panel (E) by bolts (EE) through lock washers (HH), flat washers (GG), using
Allen wrench (JJ). See figure 6.
Once all the bolts are in place. Securely tighten all the bolts (EE&FF) with Allen wrench (JJ). Base fully assembled.
7.
Hardware Used:
AA Bolt (5/16” x 30mm)
BB Flat Washer (φ8.5) x 4
CC Lock Washer (φ8.5)
x 4
Figure 7
Fix the Table Top (B) onto the Base Assembly with Bolt (AA)