Security Brands RIDGE 14-REC20 Quick Start Manual
Read Online
Read the Security Brands RIDGE 14-REC20 Quick Start Manual online using the built-in PDF viewer.
Key Pages of Document
1 of 6 2 Make sure you have all items shown here. (Screwdriver not shown) START HERE Keypad Unit Receiver 9-V Battery Key Carriage Bolt ( 4x ) Hex Nut ( 4x ) What’s what? Important components labeled Receiver Shown with cover removed. Internal wiring not shown for clarity. Keypad Unit Back of front panel shown. Internal wiring not shown for clarity. 9-V Battery Must be installed before use Connect ...
© 2020 Security Brands, Inc. All rights reserved. QSG-14500-EN Rev. B (6/2020) 2 of 6 CAUTION! The receiver is not weatherproof and must be mounted inside a weatherproof enclosure. Internal components can be damaged if exposed to the elements. Failure to comply will VOID WARRANTY. 5a Connect Receiver Ridge Receiver 12–24 VAC/DC POWER RELAY A 12–24 VAC/DC POWER Gate Operator / Door Opener POS. (+) NEG. (–) COM REVERSE LOOP ...
3 of 6 7 Add Access Code(s) to Channel A. (To add multiple codes, enter each of them before pressing pound key) 6b Pair keypad unit with receiver by entering sequence below on keypad.(Make sure 9-V battery is connected on keypad unit) A1 Additional programming 6c While pairing, keypad unit will beep and flash Once receiver LED goes out and “good” tone is heard on keypad unit, pairing is complete. LED will go out 9 LED will light solid ...
© 2020 Security Brands, Inc. All rights reserved. QSG-14500-EN Rev. B (6/2020) 4 of 6 A2 Additional programming (continued) Sub Mode Sub Mode Sub Mode Sub Mode Sub Mode Sub Mode Sub Mode Sub Mode 3 1 1 2 5 ? ? ? ? New Master Code (4 digits; numbers only) Current Master Code (1251 is default) Change Master Code 5 1 1 2 5 ? ? ? ? Latch Code (4 digits; numbers only) Channel (1 for A, 2 for B) Master Code (can be changed) ? Add Lat ...
5 of 6 B Reset Procedures Master Reset (Used if the Master Code is unknown, if the Latch Code is unknown and the unit is in Latch Mode, or if the Sleep Code is unknown and the unit is in Sleep Mode. All other codes will be retained after completing this procedure.) Step 1 - Remove front panel of keypad unit. Step 2 - Disconnect battery. Step 3 - Press and hold Reset Button; reconnect battery; then release Reset Button. Unit will sound one ...
© 2020 Security Brands, Inc. All rights reserved. QSG-14500-EN Rev. B (6/2020) 6 of 6 Notes Ridge 2.0 14-500 NEED HELP Call (972) 474-6390 Email [email protected] We are available Mon–Fri / 8am–5pm Central Model 14-REC20 ...
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipm ...
Related Devices for Security Brands RIDGE 14-REC20:
I N S T RU CTIO NS RIDGE REMOTE (433 MHZ) Model 14-R433 IN THE BOX Make sure you have everything shown here. This remote must be paired to and used with a Secur User support manual for the Security Brands 14-R433 Intercom System. It explains maintenance and technical overview, internal layout, maintenance, usage procedures.
1 of 18 Model 27-240 QUIC K S TART G UIDE 1 2 WARNING CAUTION 3 Unpack box and make sure you have all items shown here. (Screwdriver not shown.) Reference manual for the Security Brands Edge E4 Intercom System. This guide offers instructions on performance optimization, technical overview, software updates.
QUICK S TART GUI DE 1 of 6 Model 26-500 ADVANTAGE DKE 2 Make sure you have everything shown here. 3 Unlock and remove front panel of keypad unit; then using car User reference manual for the Security Brands Advantage DKE Keypad. The document contains diagnostic information, hardware components, error handling, service procedures.
ON 1 2 3 4 5 6 7 8 9 10 1 3 2 4 Coaxial Connector INSTRUCTIONS RECEIVER 300 Model 14-REC300 1 of 2 IN THE BOX Make sure you have everything shown here. Antenna Complete instruction guide for the Security Brands 14-REC300 Receiver. It provides instructions for configuration options, operating conditions, functional overview.
1 of 16 QUIC K S TART G UIDE Model 27-220 (HID, SK) 1 2 WARNING CAUTION 3 Unpack box and make sure you have all items shown here. (Screwdriver n Device guide for the Security Brands Edge E2 Intercom System. It offers guidance on performance details, technical overview, power management.
1 of 4 Model 14-RTE433T QUICK S TART GUI DE 2 Make sure you have all items shown here. (Screwdriver not shown) START HERE 1 Carefully unpack box. RTE Unit 9-V B Maintenance instructions for the Security Brands RIDGE RTE 14-RTE433T Transmitter. The document includes installation steps, troubleshooting guides, device operation tips.
1 of 6 Model 16-M1 QUIC K S TART G UIDE 1 2 STOP WARNING IMPORTANT r r Unpack box and make sure you have all items shown here. (Screwdriver not Maintenance and service manual for the Security Brands Ascent M1 Intercom System. The manual elaborates on features and wiring diagrams, installation, dimensions and layout.
1 Carefully unpack box and make sure you have all items shown below. 2 Unlock and open front panel of unit for wiring and setup. What’s what? Important compon Comprehensive setup guide for the Security Brands Ascent 16-X2 IP Access Controllers. This manual describes setup, usage, and troubleshooting, device overview, service instructions, setup.
Transceiver: Frequently Requested PDF Instructions
The Owners Manual for the Homelink® series Universal Garage Door Opener is reproduced here. HomeLink® Universal Transceiver Suggested Owner’s Manual Text Ma Complete usage guide for the HomeLink SAHL4 Transceiver. The guide offers support information and system configuration, operating modes, maintenance procedures.
Part No. 060310-10, Rev. H August 2015 OmniSwitch 10K Hardware Users Guide enterprise.alcatel-lucent.com Professional user manual for the Alcatel-Lucent OmniSwitch 10K Switch. This manual covers detailing setup, wiring diagrams, safety information, calibration steps.
UHF FM TRANSCEIVER / UHF 调频对讲机 TK-3217 © 2007-9 PRINTED IN JAPAN B51-8805-00 (S) 496 SERVICE MANUAL / 维修手册 C, C2 versions / C, C2 版本 This Quick start guide for the Kenwood TK-3217 Transceiver. This documentation explains configuration and software updates, basic operation, warranty information.
Panel Diagram Features 2 1 8 Ports Power & HD Video UTP Transceiver NO. Component Description Power Supply Input Power LED Indicate if power supply is norm Complete instruction guide for the UTEPO UTP108PV-HD Transceiver. The document guides users through device calibration, application scenarios, configuration options.