Toro 58603 Operator's Manual

Rear Tine Tiller 58603 Motocultor 58603 Motoculteur à dents arrière 58603 www.Toro.com. *3445-373* ...

Rear Tine Tiller Model No. 58603—Serial No. 321000001 and Up Register at www.Toro.com. Original Instructions (EN) *3443-831* ...

Section 4442 or 4443 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order or the engine is constructed, equipped, and maintained for the prevention of fire. WARNING CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Use of this product may cause exposure to chemicals known to the State of California to cause cancer, bi ...

General Safety ................................................... 3 Safety and Instructional Decals .......................... 4 Setup ........................................................................ 6 1 Assembling the Machine.................................. 7 2 Adding Oil to the Engine................................... 9 Product Overview ................................................... 10 Controls ........................................................... 10 Specifications ...................................................11 Before Operation .... ...

may result in personal injury or death. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal133-8062 133-8062 decal144-4853 144-4853 1. Engine—shut off decal144-4857 144-4857 1. Entanglement hazard, belt—stay away from moving parts; keep all guards in place. decal144-4861 144-4861 1. Forward lever decal144-4862 144-4862 1. Reverse lever 4 ...

decal148-4868 144-4866 1. Warning—read the Operator’s Manual. 6. Warning—look behind you when operating the machine in reverse. 2. Warning—all operators should be trained before operating the machine. 7. Warning—do not operate over buried lines. 3. Warning—keep bystanders away. 8. Warning—keep feet away from moving parts. 4. Warning—stay away from moving parts; keep all guards in place. 9. Warning—shut off the engine, disconnect the spark plug, and read the Operator’s Manual before performing maintenance. 5. Entanglement h ...

Procedure Description Qty. Use Tiller assembly 1 Handlebar assembly 1 Handlebar tube 1 Wheel 2 Lower pulley guard 1 Pulley guard plate 1 Drag stake 1 Bolt (M8 x 85 mm) 1 Bolt (M6 x 65 mm) 2 Bolt (M8 x 16 mm) 2 Bolt (M6 x 14 mm) 4 Nut (M8) 1 Nut (M6) 4 Screw 4 Pin 2 1 Lock pin 1 Assemble the machine. 2 Engine oil 1 Add oil to the engine. 6 ...

Parts needed for this procedure: 1 Tiller assembly 1 Handlebar assembly 1 Handlebar tube 2 Wheel 1 Lower pulley guard 1 Pulley guard plate 1 Drag stake 1 Bolt (M8 x 85 mm) 2 Bolt (M6 x 65 mm) 2 Bolt (M8 x 16 mm) 4 Bolt (M6 x 14 mm) 1 Nut (M8) 4 Nut (M6) 4 Screw 2 Pin 1 Lock pin Procedure 1. Remove the loose parts from the top of the box. 2. Close the box, turn it upside-down, and cut it open at the corners. 3. Cut, remove, and discard the rectangle shown on both sides of the foam. g361865 Figure 3 1. Cut here. 4. Remove the wheels. g361871 Figure 4 5. Assemble the pulley guards. g361864 Figure 5 1. Screw (4) 3. Lower pulley gua ...

wheel with the bolt. g361868 Figure 7 1. Bolt—M8 x 16 mm (2) 2. Pin (2) 8. Turn the machine over and remove the foam. 9. Install the handlebar tube as follows: A. Rotate the spreader bolt clockwise. g361872 Figure 8 1. Spreader bolt B. Insert the handlebar tube into the red bracket and secure it as shown. g361867 Figure 9 1. Nut (M8) 3. Bolt (M8 x 85 mm) 2. Handlebar tube C. Remove and discard the spreader bolt. D. Tighten the fasteners until the handlebar tube is snug. 10. On the handlebar assembly, connect the cables to the drive levers if they are not attached. g361873 Figure 10 1. Rear drive leve ...

the height as desired; refer to Adjusting the Handlebar Height (page 13). g361870 Figure 11 1. Nut—M6 (2) 3. Bolt—M6 x 65 mm (2) 2. Wire harness connectors 12. Connect the 2 wire harness connectors. 13. Install the drag stake. g361869 Figure 12 1. Drag stake 2. Lock pin 2 Adding Oil to the Engine Parts needed for this procedure: 1 Engine oil Procedure 1. Move the machine to a level surface. 2. Remove the dipstick. g360549 Figure 13 1. Filler tube 3. Upper limit 2. Dipstick 4. Lower limit 3. Slowly add oil into the filler tube until it is overflowing. 4. Install the dipstick and tighten it. 9 ...

7. Handlebar height adjustment 2. Forward control lever 8. Fuel cap 3. Rear control lever 9. Engine controls 4. Cable adjustment 10. Oil-fill cap 5. Drive-mode selector lever 11. Drag stake 6. Recoil handle Controls Engine On/Off Switch Use the engine On/Off switch to shut the engine off. Ensure that the switch is in the ON position before starting the engine. Fuel-Valve Lever Move the lever for the fuel valve to the ON position before attempting to start the engine. After operation, shut off the engine and move the fuel-valve lever to the OFF position. Throttle Control The throttle controls th ...

engine; the tines are disengaged. Use this mode for powered transportation when driving up steep inclines and moving the machine to and from your garden. g356988 Figure 16 • Counter-rotating tines (CRT): The wheels and tines are both engaged with the engine; the tines spin in the opposite direction of the wheels. Use this mode when breaking new ground or tilling in compacted soil conditions. g356987 Figure 17 • Neutral: The wheels and tines are both disengaged from the engine. Use this mode for storage and non-powered transportation. g356989 Figure 18 Drive-Control Levers Pull down the forward lever t ...

machine from the normal operating position. Before Operation Before Operation Safety General Safety • Do not allow children or untrained adults to operate or service the machine. Local regulations may restrict the age of the operator. • Using this machine is strenuous. You must be in good physical condition and mentally alert. If you have any condition that might be aggravated by strenuous work, check with your doctor before operating the machine. • Shut off the machine and wait for all moving parts to stop before you leave the operator’s position. Disconnect the spark-plug wire, keep it ...

87 (US) or 91 (research octane; outside the US) Ethanol No more than 10% by volume Methanol None MTBE (methyl tertiary butyl ether) Less than 15% by volume Oil Do not add to the fuel Use only clean, fresh (no more than 30 days old), fuel from a reputable source. Using Stabilizer/Conditioner Use fuel stabilizer/conditioner in the machine to keep the fuel fresh longer when used as directed by the fuel-stabilizer manufacturer. Important: Do not use fuel additives containing methanol or ethanol. Add the amount of fuel stabilizer/conditioner to fresh fuel as directed by the fuel-st ...

General Safety • Use your full attention while operating the machine. Do not engage in any activity that causes distractions; otherwise, injury or property damage may occur. • Do not operate the machine while ill, tired, or under the influence of alcohol or drugs. • Wear appropriate clothing, including eye protection; long pants; substantial, slip-resistant footwear; hearing protection; and gloves. Tie back long hair and do not wear loose clothing or loose jewelry. • Keep your hands, feet, other body parts, and clothing away from rotating tines and moving parts of the machine. The tines begin rotating wh ...

1. Move the engine on/off switch to the ON position. 2. Move the fuel-valve lever to the OPEN position. 3. Move the throttle lever to the FAST position. 4. Move the choke lever to the CHOKE position. Note: A warm or hot engine may not require choking. 5. Pull the starter handle lightly until you feel resistance, then pull the handle briskly. Return the starter handle gently. 6. After the engine starts, gradually move the choke lever to the RUN position and the throttle lever to the FAST position. Shutting Off the Engine 1. Release the drive-control levers. 2. Move the throttle lever to the SLOW position. 3. Move the engine on/off s ...

and remove all objects such as large rocks, trash, and branches before tilling to prevent equipment damage. • Do not place excessive body weight on the machine. Use the weight of the machine to till the soil more efficiently. • When tilling, begin with a shallow cut on the first pass and then increase the depth by 2.5 to 5.1 cm (1 to 2 inches) on each successful path until you reach the desired depth. • Plant garden rows 51 to 56 cm (20 to 22 inches) apart to allow ease of turning at the end of each row. • When not tilling, move the throttle lever between half throttle and the S ...

is in safe working condition and that shear bolts, engine-mounting bolts, and other fasteners are properly tightened. • Shut off the machine and wait for all moving parts to stop before you leave the operator’s position. Disconnect the spark-plug wire, keep it away from the plug to prevent accidental starting, and allow the machine to cool before adjusting, fueling, unclogging, servicing, cleaning, or storing the machine. • Wear gloves and eye protection when servicing the machine. • Never tamper with safety devices. Check their proper operation regularly. • T ...

1. Move the machine to a level surface, shut off the engine, and wait for all moving parts to stop. 2. Disconnect the spark-plug wire from the spark plug. g361695 Figure 23 1. Spark-plug wire 3. After performing the maintenance procedure(s), connect the spark-plug wire to the spark plug. Important: Before tipping the machine, allow the fuel tank to run dry through normal usage. If you must tip the machine prior to running out of fuel, use a hand fuel pump to remove the fuel. Lubrication Greasing the Machine Grease type: White lithium grease Grease the machine at the following locations: • Forward a ...