SECURECOM SC-GSM Manual 

Text of SECURECOM SC-GSM Manual 

SC-GSM Alarm Signaling Communicator v1.3

1 EN SSCC--GGSSM M Analog phone line simulator (GSM gateway) or translation of Contact ID signals to SMS messages and alarm calls. One device with 2 independent operating modes. Manual v1.3
SC-GSM Alarm Signaling Communicator v1.3 2 EN Table of Contents 1 Short functional description of device .................................................................................................. 3 1.1 Main features ............................................................................................................................. 3 1.2 Technical specifications ...............................................................................
SC-GSM Alarm Signaling Communicator v1.3 3 EN 1 Short functional description of device In Standalone mode the unit behaves like a monitoring station receiver which receives and handles the CONTACT ID communication of alarm control devices. It compares the report codes with the filled in event codes of the program table and at the occurrence of the desired event it sends the assigned SMS message and initiates a call (siren sound is played). By this means th
SC-GSM Alarm Signaling Communicator v1.3 4 EN 2 Product Layout Sign Part Description ANTENNA CONNECTOR GSM network antenna Connector type: SMA, Impedance: 50 ohm, Frequency: 900/1800 MHz SIM CARD HOLDER For mobile network connection Type: GSM voice band card, Dimension: 2FF mini SIM LED status display The LED status signals USB CONNECTOR For parameters setting, the communicator must be connected to the computer through USB port. Type: USB mini-B DC POWER
SC-GSM Alarm Signaling Communicator v1.3 5 EN 3 Connection In order to operate properly, the device must be equipped with a valid SIM card and the external antenna must be connected to the antenna connector. Use the supplied antenna or any other GSM antenna that suites the needs for installation. The SIM card should be inserted to the card holder “door” (the moving part of card holder), as shown on picture. The Door must be pushed toward the PCB until
SC-GSM Alarm Signaling Communicator v1.3 6 EN 4 Configuration of device Connect the device with USB cable to a windows PC (Compatibility: Windows 7, 8.1, and 10), and a new drive will be installed. When connected to that machine for first time, the driver will be installed first, then the new drive will be found. This drive is the flash memory of SC-GSM device, and contains the software and this manual. You can run the software from device, or copy it to y
SC-GSM Alarm Signaling Communicator v1.3 7 EN 4.2 Moving data between the PC and the device Reading out data from the device happens automatically as soon as connection is established. Settings can be saved to PC or loaded from PC file. These icons are used to handle the settings data: (File_reading / File_saving / Download to device ) IMPORTANT NOTICE: if a new settings file is loaded or ANY setting is modified on software screen, all data needs to be
SC-GSM Alarm Signaling Communicator v1.3 8 EN 4.5 General setting The General setting parameters are valid for both operating modes, and in this area the operating mode (transparent or standalone) is selected 4.6 Transparent mode In this mode, device can be used as a transparent GSM Gateway, to forward voice signals (DTMF or speech) from a phone device or alarm panel through a GSM network, to called party or a monitoring station receiver. The phone device
SC-GSM Alarm Signaling Communicator v1.3 9 EN Z1 and Z2 contact inputs are used as inputs of independent alarm communicator, triggering them causes the sending of programmed event code (Contact ID protocol) to the programmed Receiver Phone Number, paired with the programmed Account Id. The partition number in the message is 01 and the value of the zone in the message is 001 and 002 and they cannot be changed. Communication format is CONTACT ID. You can fin
SC-GSM Alarm Signaling Communicator v1.3 10 EN In the example , the received Contact ID code /8556 18 1 401 01 001/ means that a system with ID number (“account number”) 8556, has sent a signal that EVENT (1) of ARMING (401) was made in Partition 01, by user 001. With settings as shown on picture on top of this page, Appropriate SMS message for this code ,”ANGIE left home” (Angie is user 001), will be sent to sent to T1 telephone number. Ano

SECURECOM Gateway Owners Instructions: