Roca LUMEN Installation Manual

Installation requirements............................................................................4 Product carton contents.............................................................4 Power supply................ ...

Safety precautions These safety precautions are essential for safe installation and use of the shower toilet. Please read the precautions thoroughly before installing the product properly and prevent accidents in use. DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates dangerous situations where the user could suffer death or serious injury ...

seats (toilet cleanser, home cleanser, bleach, benzene, paint thinner, scouring powder, cresol). To prevent damage to seat or lid, do not stand on lid or lean against lid while sitting on seat. Do not nick, damage, carve, bend unduly, pull on, twist, bind or place heavy objects on top of the power cord, or pinch it between two objects. *The above could damage the elec ...

Installation requirements Before installing this product, ensure that each of the following installation requirements is met. Product carton contents Remove the parts from the product carton and make sure all the parts in the parts list (below) are present. Inspect the parts carefully to make sure they are in good condition. If any part is damaged or missing, do not install the Shower Toilet. Contact the nearest sales outlet for th ...

* The length of the power cord is 1.2 m. Install the outlet within reach of the power cord in a water-free position above the floor level. * Be sure to ground the outlet. - Ask a qualified electrical contractor to install the wiring for the power supply. - Do not insert the power plug in the outlet until installation is completely finished. Doing so may cause system failure. * This ...

The remote control unit should be mounted on the wall which is on the side where the toilet's remote control light receptor is located (left side). If it is necessary to mount the remote control unit on the opposite wall side, make sure the remote control signals can be received from that position. In the case also that the remote control unit's light receptor side wall has a wash stand installed and there is quite s ...

Body Flush Lever Toilet Strainer (See figure below.) Power Plug Open / Close Handle Water Supply Hose Mounting Base Toilet Seat Nozzle (for bidet) Nozzle (for posterior) Warm Water Tank Drain Plug and Shower Toilet Strainer (See figure below.) Water Shutoff Valve Warm Water Tank Drain Plug Shower Toilet Strainer Toilet Strainer Drain Socket Remote Control Unit Names of parts Caution Label Marking Label ...

CAUTION: Do not get your hand caught in the water shutoff valve or step on it. * It could cause the pipe to become unstable or damage it, causing water leakage. * There is danger of marring the wall or the floor. Install the water supply outlet in the proper direction so that the water shutoff valve won’t cause bending of the water supply hose. After finishing the walls and floor, install the water sup ...

(5) Align the collar of the mounting base with the collar of the drain socket to fix the position of the mounting base. (6) Drill a pilot hole (S10) for the mounting base, and strike the locally procured plastic anchor (S10). (7) Apply silicone on the edge of the drain socket to seal it. See the figure on the previous page for the area to apply silicone. CAUTION: Fix the mounting base on the floor before silicone ...

(Body side) Install the water supply hose in a direction so that it is not bent when connected. (1) Insert the end of the water supply hose in the water supply inlet of the body. CAUTION: Be careful not to damage the O-ring. * Water may leak if the O-ring is broken or damaged. Remove the cap in the water supply hose immediately before connecting it to the water shutoff valve. * There is danger of dirt, etc. getting in ...

(1) Remove the protective cover and protective cap. Remove the protective cover from the toilet bowl, and then remove the protective cap from the body. (2) Install the flat packings. Install the flat packings on the 2 mounting bolts on the bottom of the body. * Install the flat packings so that the body cover does not get any flaw. Installation Diagram Protective Cover Protective Cap Mounting Bolt Flat Packing ...

Place the mounting bolts on the bottom of the body in the 2 mounting holes in the back of the toilet bowl to install the body. CAUTION: Do not take hold of the flush handle to life the body. * The body or the flush handle could become damaged. Make sure the body is sitting firmly on the toilet bowl. * There is danger of water leaking from the water inlet to the toilet if the body is not seated firmly on the toilet. (4 ...

(Water shutoff valve side) (1) Remove the cap from the end of the water supply hose, then insert it in the water supply outlet. CAUTION: Be careful not to damage the O-ring. * Water may leak if the O-ring is broken or damaged. Remove the cap in the water supply hose immediately before connecting it to the water shutoff valve. * There is danger of dirt, etc. getting inside the water supply hose while the work is procee ...

(1) Insert the power plug in the wall outlet. CAUTION: Be sure to turn on the power only after installation of the product is completed. Do not insert the power plug in the outlet while touching the toilet seat. The shower nozzle (posterior, bidet) may not extend if this happens. If the shower nozzle does not extend, pull out the power plug, then insert it again without touching the toilet seat. (2) Confirm that the syste ...

(1) Place the bracket on the wall so that it aligns with the internal wall frame, then mount it in the desired mounting position. If mounted in plywood paneling 5 mm or greater in thickness: Fasten the bracket to the wall with the wood screws. If mounted either in plywood paneling 5 mm or less in thickness or in gypsum board: 1) In plywood paneling, drill holes with a diameter of 6 mm; in gypsum board, drill holes wit ...

(1) Turn the Open/Close handle of the water shutoff valve to the fully open position and turn on the flow of water to the shower toilet. (2) Check to make sure there is no water leakage. 1) Operate the remote control unit, flushing the toilet several times. 2) Check each of the connections for water leakage. At the same time, check if there is anything abnormal about the operation of the flush lever, etc. CAUTION: Repeat the test ...

* Since there is an occupied seat sensor, the shower toilet's shower, bidet and deodorizing functions will not operate if you don't touch the seat. Roll up your sleeve and bring your bare arm in direct contact with the toilet seat. 1. Check the shower washing operation. (1) Rest your arm on the toilet seat, then press the POWERFUL shower button. It takes 1 to 2 minutes for the tank to fill and for water ...

(1) Close the water shutoff valve's Open/Close handle. CAUTION: Do not remove the strainer with the water shutoff valve opened. * Doing so may cause water leakage from the strainer. (2) Press the flush button on the remote control unit. (3) Remove the side panel on the left side of the toilet, then place a wash basin, etc. underneath and remove the strainer for the toilet. (4) Place the wash basin, et ...

the product to the customer. (1) Close the water shutoff valve's Open/Close handle. CAUTION: Do not remove the strainer with the water shutoff valve opened. * Doing so may cause water leakage from the strainer. (2) Turn the flush lever counterclockwise. (3) Remove the side panel on the left side of the toilet, open the strainer and drain the water out of the water shutoff valve. (4) Place a wash ...

Avda. Diagonal, 513 08029 Barcelona España Tel. +34 (93) 366 12 00 ...