Texas Instruments MSP430F51 Operation & User’s Manual
Read Online
Read the Texas Instruments MSP430F51 Operation & User’s Manual online using the built-in PDF viewer.
Key Pages of Document
User’s Guide Literature Number: SLAU278AH MAY 2009 – REVISED MARCH 2021 ...
How to Use This Manual..........................................................................................................................................................7 Information About Cautions and Warnings....................................................... ...
B.20 MSP-TS430RGZ48B......................................................................................... ...
Figure B-25. MSP-TS430RHB32A Target Socket Module, PCB............................................................................................... 67 Figure B-26. MSP-TS430DA38 Target Socket Module, Schematic...........................................................................................69 Figure ...
Figure B-87. MSP-TS430PEU128 Target Socket Module, PCB..............................................................................................174 Figure B-88. EM430F5137RF900 Target Board, Schematic................................................................................................... 176 Fig ...
program development tool for the MSP430™ ultra-low-power microcontrollers. How to Use This Manual Read and follow the instructions in Chapter 1. This section lists the contents of the FET and provides instructions on installing the hardware and the software drivers. After you see how quick and easy it is to use the development tools, TI recommends that you ...
This document may contain cautions and warnings. CAUTION This is an example of a caution statement. A caution statement describes a situation that could potentially damage your software or equipment. WARNING This is an example of a warning statement. A warning statement describes a situation that could potentially cause harm to you. The information in a caution or a warning is provided for your protection. Read each ...
MSP430FR58xx, MSP430FR59xx, and MSP430FR6xx Family User's Guide If You Need Assistance Support for the MSP430 devices and the FET development tools is provided by the Texas Instruments Product Information Center (PIC). Contact information for the PIC can be found on the TI website at www.ti.com/support. The Texas Instruments E2E™ Community support forums for the MSP430 provide open interaction with peer engineers, TI engi ...
www.ti.com 10 MSP430™ Hardware Tools SLAU278AH – MAY 2009 – REVISED MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated This page intentionally left blank. ...
1.1 Kit Contents, MSP-TS430xx.......................................................................................................................................12 1.2 Kit Contents, MSP-FET430xx.....................................................................................................................................14 1.3 Kit Contents, MSP-FET...... ...
• One READ ME FIRST document • One 32.768-kHz crystal from Micro Crystal (except MSP-TS430PW24) • One target socket module • A 2×7-pin male JTAG connector is also present on the PCB (see different setup for L092) • MSP430 MCU samples (see Table 1-1 for sample type) Table 1-1. Individual Kit Contents, MSP-TS430xx Part Number Socket Type Supported Devices Included Devices Headers and Comment MSP-TS430D8 (green PCB) 8- ...
Part Number Socket Type Supported Devices Included Devices Headers and Comment MSP-TS430PM64 (green PCB) 64-pin PM (QFP ZIF) MSP430F13x, MSP430F14x, MSP430F14x1, MSP430F15x, MSP430F16x, MSP430F16x1, MSP430F23x, MSP430F24x, MSP430F24xx, MSP430F261x, MSP430F41x, MSP430F42x, MSP430F42xA, MSP430FE42x, MSP430FE42xA, MSP430FE42x2, MSP430FW42x TS Kit: 2 × MSP430F2618IPM; FET Kit: 2 × MSP430F417IPM and ...
• One READ ME FIRST document • One MSP-FET430UIF USB interface module. This is the unit that has a USB B-connector on one end of the case, and a 2×7-pin male connector on the other end of the case. • One USB cable • One 32.768-kHz crystal from Micro Crystal, if the board has an option to use the quartz. • A 2×7-pin male JTAG connector is also present on the PCB (see different setup for L092) • One 14-Pin JTAG co ...
• One QUICK START GUIDE document • One eZ430-RF2500 CD-ROM • One eZ430-RF2500 development tool including one MSP430F2274 and CC2500 target board • One eZ430-RF2500T target board • One AAA battery pack with expansion board (batteries included) 1.9 Kit Contents, eZ430-RF2500T • One eZ430-RF2500T target board • One AAA battery pack with expansion board (batteries included) 1.10 Kit Contents, eZ430-RF2500-SEH • On ...
• One READ ME FIRST document • One legal notice • One MSP-FET430UIF interface module • Two EM430F6137RF900 target socket modules. This is the PCB on which is soldered a CC430F6137 device in a 64-pin RGC package. A 2×7-pin male connector is also present on the PCB. • Two CC430EM battery packs • Four AAA batteries • Two 868-MHz or 915-MHz antennas • Two 32.768-kHz crystals • 18 PCB 2x4-pin headers • On ...
EM430Fx1x7RF900 Follow these steps to install the hardware for the MSP-FET430Uxx and MSP-TS430xxx tools: 1. Install the IDE (CCS or IAR) you plan to use before connecting USB-FET interface to PC. The IDE installation installs drivers automatically. 2. Use the USB cable to connect the USB-FET interface module to a USB port on the PC. The USB FET should be recognized, as the USB devic ...
www.ti.com 18 MSP430™ Hardware Tools SLAU278AH – MAY 2009 – REVISED MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated This page intentionally left blank. ...
2.1 Signal Connections for In-System Programming and Debugging.........................................................................20 2.2 External Power............................................................................................................................................................24 2.3 Bootloader (BSL)......................................... ...
MSP-FET430PIF, MSP-FET430UIF, MSP-GANG, MSP-GANG430, MSP-PRGS430 With the proper connections, the debugger and an FET hardware JTAG interface (such as the MSP-FET430PIF and MSP-FET430UIF) can be used to program and debug code on the target board. In addition, the connections also support the MSP-GANG430 or MSP-PRGS430 production programmers, thus providing an easy way to program prototype board ...
