Thunder TDR02026 Instruction Manual

the information provided in this instruction manual. THANK YOU FOR CHOOSING THE THUNDER BATTERY MANAGEMENT SYSTEM ...

4. Installation 5. Operation 5. Charging Stages 7. LCD Display Operation 8. Display 9. Wiring 10. Specifications 11. Warranty Terms & Conditions Copyright © 2020 GPC Asia Pacific Pty Ltd ABN 97 097 993 283 CONTENTS ...

• Heavy duty aluminium housing. • 8 Stage charging for 240VAC and DC-DC charging, when not in lithium mode. • 3 stage charging for 240VAC, DC-DC and solar charging battery when in lithium mode. • 30A 240V charging. • 30A DC-DC charging. • Solar input with MPPT regulated output (50V 500W max). • 12-24V system input (12V output). • 0-50° Operating Temperature. • Internal charger temperature monitoring and power output control. • Over charging, short circuit and over temperature protection. • Output reverse polarity protection. • Removable 3.5 inch Bluetooth colour LCD display with touch screen functionality ...

• Connect the wire from the main starting battery of the vehicle to the input red stud on the rear of the TDR02026 charger using suitable cable (see specification table on page 9), it is recommended to place a circuit breaker (50A minimum, not supplied) in the main positive lead as close as possible to the starting battery. • Connect the positive wire from the auxiliary battery to the output red stud on the front of the TDR02026 charger, ensure the correct size cable is used to prevent any voltage drop (see specification table on page 9). • Connect the n ...

to charge a 12V auxiliary battery. The unit can also be used to connect solar panels and can charge either the 12V starter battery of a vehicle or the 12V auxiliary battery depending on which battery has lower voltage. The priority of charge for the TDR02026 is to prioritise 240VAC charge first, then DC-DC Vehicle charging, then Solar panel charging. This means that if the 240VAC plug is plugged in and powered, while also having solar panel connected, the 240VAC ch ...

Stage 1: Direct solar energy to charge the battery until the battery voltage reaches 14.5V, switches to stage 2. Stage 2: Overpressure pulse charging, when the battery voltage is lower than 14.5V, charger pulses for 1 sec on and 1 sec off. This will occur for 2 hours, or until 14.5V average is reached whichever comes first. Then will switch to Stage 3. Stage 3: Pulse floating charge, pulse 1 sec on 1 sec off at 13.8V Stage 1: Charging with increasing voltage and constant output current. Stage 2: Perform constant voltage charging at 14.5V, when current is lower than 3A, switch to stage 3. Stage 3: Performs float charging wi ...

screen, allowing you to have a better visibility of your batteries health and charging inputs. You can now monitor the health and usage of your battery allowing you to know what is charging your batteries and how long you have left until they are flat, At a glance you can tell if you need to start the generator or move the Solar to ensure you get the maximum input to your batteries. A lithium charging profile has been added so you can decide what battery system you would like to run. If there is a fault with the auxiliary battery the LCD screen will show a fault symbol to ...

will be blue when any of the charging modes are charging the auxiliary battery. The top left icon will only turn green when solar input is charging the starting battery as seen in the image below. The centre top of the LCD screen shows the selected Ah of the connected auxiliary battery, this must be adjusted pressing the “AH select” button on the bottom left corner of the LCD touch screen. The AH value increments by 5 Ah every time “AH select” is pressed. The top right icon shows output current from anything connected through the shunt. The oval s ...

• 0 - 10 metres 6 B&S/6AWG* • Over 10 metres Consult an auto electrician Circuit Protection • 50A Circuit breaker on TDR02026 Input Cable • Mounting of the TDR02026 needs to be within 1M of the batteries you would like to charge * When fitting the TDR02026 to a caravan or camper trailer, the cable will need to be connected to the towing vehicle with a suitable heavy-duty connector such as a 50A “Anderson” connector or similar. Screen Wiring Red: Positive Black: Negative UNIT WIRING Rear Wiring: Red Stud: 12/24V Input Small Stud: Solar Positive Input Front Wiring: Red: 12V Output Black: ...

DC-DC 8 Stages Lithium Charging Stages 240VAC, DC-DC, Solar 3 Stages Normal Charging Stages Solar input 3 Stages Charging Modes 240VAC, DC-DC charging, Solar Charging Output current 30A AC input voltage 200VAC – 260VAC Input Fuse Rating 50A DC-DC charging input voltage 12.2V - 32V *(If voltage increases over 32V the Thunder DC-DC will shut off, reset will be needed by disconnecting all inputs) Min and maximum Charging Voltages 13.1V - 15.2V (stops charging when alternator or vehicle battery below 12.2V) AGM Float Voltage 13.8V Lithium Voltages 14.1 Bulk, 13.1 Float Solar input voltage 13V-50V Solar Regulator MPPT Aux ...

workmanship. The Thunder warranty is provided in addition to any rights you may have under the Australian Consumer Law. All claims under this warranty should be made by returning the product to the place of purchase at your expense, with the detail of the fault, proof of purchase and fitment details. If we determine that a Thunder product is defective in materials or workmanship during the warranty period, we will either repair or replace the unit. This warranty does not apply to failur ...

22 Enterprise Drive Rowville Victoria 3178 Australia 510 Mt Wellington Hwy Auckland New Zealand thunderauto.com.au // thunderauto.co.nz GPC Asia Pacific 22 Enterprise Drive Rowville Victoria 3178 Australia 510 Mt Wellington Hwy Auckland New Zealand thunderauto.com.au // thunderauto.co.nz ...