Weider Pro 9020 Manual 

Text of Weider Pro 9020 Manual 

Model No. 831.15501.0

Serial No. Write the serial number in the space above for reference. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Keep this manual for future reference. Serial Number Decal •• Assembly •• Operation •• Maintenance •• Part List and Drawing Sears, Roebuck and Co. Hoffman Estates, IL 60179 WEIGHT SYSTEM EXERCISER User’’s Manual

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. It is the responsibility of the owner to ensure

that all users of the weight system are adequately informed of all precautions. 2. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or per- sons with pre-existing health problems. 3. Use the weight system only as described in this manual. 4. The weight system is intended for home use only. Do not use the weight syste

High Pulley Station

Lat Bar Backrest Ab Pulley Station Press Arm Weight Stack Weight Pin Right Side Left Side Note: The terms ““right side”” and ““left side”” are determined relative to a person sitting on a seat; they do not correspond to right and left on the drawings in the manual. Backrest Low Pulley Station Leg Lever Curl Pad Seat Seat Butterfly Arm BEFORE YOU BEGIN Thank you for selecting the versatile WEIDER PRO™™ 9020 DU

Weider Pro 9020 13mm Spacer (86)

16mm Spacer (100) 24mm Spacer (87) 38mm Spacer (105) 48mm Spacer (81) PART IDENTIFICATION CHART Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. Note: If a part is not in the hardware kit,

M10 x 95mm Bolt (83)

M10 x 117mm Bolt (89) M10 x 68mm Bolt (98) M10 x 70mm Bolt (99) M10 x 75mm Bolt (113) M10 x 115mm Bolt (97) M10 x 65mm Bolt (85) M10 x 50mm Bolt (102) M10 x 55mm Bolt (82) M10 x 45mm Bolt (95) M10 x 20mm Screw (101) M10 x 45mm Hex Bolt (112) M10 x 59mm Bolt Set (115) M10 x 107mm Bolt Set (104) ST4.2 x 16mm Screw (90) ST4.2 x 10mm Screw (117) M6 x 16mm Screw (88) M6 x 65mm Screw (106) M6 x 40mm Screw (91)

•• To watch an assembly

video, go to http://productvideo.co/ assembly/sears/wei- der or use your mobile phone or smartphone to read the QR code at the right. •• Assembly requires two persons. •• Because of its weight and size, assemble the weight system in the location where it will be used. Make sure that there is enough clearance around the weight system. •• Place all parts in a cleared area and remove the packing materials. Do not dispose

2. Identify the Short Base (17) and the Weight

Stack Base (109). Orient both parts as shown. Attach the Short Base (17) to the Weight Stack Base (109) with two M10 x 68mm Bolts (98), two M10 Washers (93), and an M10 Locknut (84); do not tighten the Bolts yet. 3. See the inset drawing. Identify the Long Base (1). Attach the Long Base (1) to the Weight Stack Base (109) with two M10 x 68mm Bolts (98), two M10 Washers (93), and an M10 Locknut (84); do not ti

4. Identify the Right and Left Uprights (2, 14).

Orient both parts as shown. Attach the Left Upright (14) to the Short Base (17) with two M10 x 115mm Bolts (97), four M10 Washers (93), and two M10 Locknuts (84); do not tighten the Bolts yet. Attach the Right Upright (2) to the Long Base (1) in the same way. 5. Attach the Right Upright (2) to the Left Upright (14) with two M10 x 68mm Bolts (98) and two M10 Washers (93); do not tighten the Bolts yet. 4 5 1

6. Orient the Weight Guides (29) so that the indi-

cated holes are in the locations shown. Attach a Weight Guide (29) to the Weight Stack Base (109) with an M10 x 65mm Bolt (85), two M10 Washers (93), a 13mm Spacer (86), and an M10 Locknut (84); do not tighten the Bolt yet. Attach the other Weight Guide (29) in the same way. 7. Slide two Round Weight Bumpers (48) onto each Weight Guide (29). Next,

8. Orient the Weight Stack Top (13) as shown. Set

the Weight Stack Top on the Weight Guides (29). Attach the Weight Stack Top (13) to the Right and Left Uprights (2, 14) with four M10 x 68mm Bolts (98), four M10 Washers (93), and two M10 Locknuts (84); do not tighten the Bolts yet. 9. Attach a Weight Guide (29) to the Weight Stack Top (13) with an M10 x 65mm Bolt (85), two M10 Washers (93), a 13mm Space

10. Using a plastic bag to keep your fingers clean,

apply some of the included grease to an M10 x 95mm Bolt (83). Attach the Leg Press Frame (5) to the Long Base (1) with the M10 x 95mm Bolt (83) and an M10 Locknut (84). Do not overtighten the Locknut; the Press Frame must pivot easily. 11. While a second person holds the Foot Plate (6) against the Leg Press Frame (5), insert the Foot Plate Tube (7) through the Foot Plate

12. Identify the Right and Left Press Arms (11, 12)

and the Press Arm Bracket (25). Orient the parts as shown. Attach the Right and Left Press Arms (11, 12) to the Press Arm Bracket (25) with three M10 x 70mm Bolts (99) and three M10 Locknuts (84); do not tighten the Bolts yet. 13. Apply grease to an M10 x 95mm Bolt (83). Attach the Right and Left Press Arms (11, 12) to the Long Base (1) with the M10 x 95mm B

Weider Pro 9020 14. Apply grease to an M10 x 59mm Bolt Set (115).

Attach the Left Press Handle (10) to the Left Press Arm (12) with the M10 x 59mm Bolt Set (115). Attach the Right Press Handle (9) to the Right Press Arm (11) in the same way. Grease 15. Attach the Right Seat Frame (4) to the Long Base (1) with two M10 x 115mm Bolts (97), four M10 Washers (93), and two M10 Locknuts (84); do not tighten the Bolts yet.

16. Attach the Right Seat Frame (4) to the Right

Upright (2) with two M10 x 68mm Bolts (98) and two M10 Washers (93); do not tighten the Bolts yet. 17. Attach the Right and Left Seat Handles (8, 32) to the Right Seat Frame (4) with two M10 x 117mm Bolts (89) and two M10 Locknuts (84).

18. Attach the Lat Bar Bracket (15) to the Left

Upright (14) with two M10 x 68mm Bolts (98) and two M10 Washers (93). 19. See the CABLE DIAGRAMS starting on page 40 to identify the cables. Locate Cable B (64). Hold the ends of Cable B near the center of the Butterfly Arm (23) as shown. Locate the two wire ties in the center of the Butterfly Arm (23). Tie one wire tie to each end of Cable B (64) as shown. Next, pull

Weider Pro 9020 20. While a second person holds the Butterfly Arm

(23) near the Left Upright (14), insert the loop of Cable B (64) through the hole in the Left Upright. Attach the Butterfly Arm (23) to the Left Upright (14) with two M10 x 68mm Bolts (98), two M10 Washers (93), two 48mm Spacers (81), an M10 Large Washer (116), and an M10 Locknut (84); do not tighten the Bolts yet. 21. Insert a V-pulley (

Weider Other Owners Instructions: