Sauder 415107 Manual 

BEFORE RETURNING YOUR UNIT TO THE STORE 1-800-523-3987 www.sauder.com Made in the USA Archbold, OH NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Lot #: 355628 10 / 07 / 13 Date Purchased: ____________________ English .................... Page 1-24 Français ...............Pages 25-28 Espanol .............Páginas 29-32 415107 Armoire Carson Forge Collection ...

Hammer No. 2 Phillips Screwdriver Tip Shown Actual Size ADULT ASSEMBLY REQUIRED TABLE OF CONTENTS Part Identifi cation .......................3 Hardware Identifi cation .............4 Assembly Steps .................... 5-24 Français .............................. 25-28 Espanol ............................... 29-32 Safety ................................. 33-34 Warranty ...................................35 Page 2 www.sauder.com/ ...

letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help identify similar parts. A RIGHT END 1 B LEFT END 1 C TOP 1 D BOTTOM 1 E SHELF 1 F BACK 1 G SKIRT 1 H DOOR 2 I RIGHT FOOT 1 J LEFT FOOT 1 K TOP MOLDING 1 L DRAWER FRONT 1 M SHELF MOLDING 1 N BOTTOM MOLDING 1 O DRAWER BRACE 1 D132 RIGHT DRAWER SIDE 1 ...

CABINET LEFT - 1 35GC DRAWER RIGHT - 1 35GD DRAWER LEFT - 1 FOOT CAP - 2 10E CORNER BRACKET - 2 31G SLIDE CAM - 2 10A 52K KNOB - 2 13H HINGE - 6 CAM SCREW - 9 8F HIDDEN CAM - 9 1F TIE PLATE - 2 3G LARGE RUBBER SLEEVE - 2 24G 7A ROD HANGER - 2 TACK GLIDE - 2 12E TWIST-LOCK® FASTENER - 12 7F METAL BRACKET - 6 4G SAFETY BRACKET - 1 1G 15F WOOD DOWEL - 6 ...

Page 5 www.sauder.com/services 415107 5L WARNING LABEL - 1 (Refer to step 20 for proper location and application) WARNING ! Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over: • Place heaviest items in the lowest drawers. • Unless specifi cally designed to accommodate, do not set TVs or other heavy objec ...

assembly tip is available at: www.sauder.com/services/tips 1 S t e p Assemble your unit on a carpeted fl oor or on the empty carton to avoid scratching your unit or the fl oor. To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (7F) into the large holes in the ENDS (A and B). Repeat this step for the BOTTOM (D) and SHELF (E). Page 6 www.sauder.com/services 415107 Do not tighten the TWIST-LOCK® FASTENERS in this s ...

Insert eight SUPPORT PINS (5R) into the ENDS (A and B). 5R 7A SILVER 1/2" FLAT HEAD SCREW (2 used in this step) 78S ...

BOTTOM MOLDING (N). Push nine HIDDEN CAMS (1F) into the BOTTOM (D), SHELF (E), SKIRT (G), and DRAWER BRACE (O). (9 used) 8F Do not tighten the HIDDEN CAMS in this step. Arrow 1F Arrow 1F Arrow (9 used) 1F D E G O Page 8 www.sauder.com/services 415107 ...

5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. GOLD 5/16” FLAT HEAD SCREW (4 used in this step) 3S 1 2 3 3 2 1 Roller end Finished edge Finished edge Surface with TWIST-LOCK® FASTENERS Surface with TWIST-LOCK® FASTENERS Page 9 www.sauder.com/services 415107 ...

Surface with TWIST-LOCK® FASTENERS Surface with holes Surface with TWIST-LOCK® FASTENERS Rounded edge Edge with holes Dowel end How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted ...

the excess GLUE. Next, fill the hole in BOTTOM (D) 1/4 to 1/2 full with GLUE (8M). Fasten the LEFT END (B) to the BOTTOM (D). Push the WOOD DOWEL (15F) in the LEFT END (B) into the hole in BOTTOM ( ...

(10 used in this step) 1S Fasten two METAL BRACKETS (4G) to the BOTTOM (D). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten two CORNER BRACKETS (31G) to the ENDS (A and B) and BOTTOM (D). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the BRACKETS are even with the edges of the ENDS (A and B) and BOTTOM (D). 4G 31G 31G B D Page 12 www.sauder.com/services 415107 ...

These holes must be here. Flat edge Flat edge Surface with HIDDEN CAMS ...

away the excess GLUE. Fill the large holes in the FEET (I and J) 1/4 to 1/2 full with GLUE (8M). Quickly, flip the FEET over and insert the WOOD DOWELS (15F) in the ENDS into the holes in the FEET. Wipe away the excess GLUE. Fasten the FEET (I and J) to the ENDS (A and B). Use four BLACK 9/16" LARGE HEAD SCREWS ( ...

Fill the holes in the BOTTOM MOLDING (N) 1/4 to 1/2 full with GLUE (8M). Then, insert a WOOD DOWEL (15F) into these holes. Wipe away the excess GLUE. Fill the two outer holes in the BOTTOM (D) 1/4 to 1/2 full with GLUE (8M). Insert the WOOD DOWELS (15F) in the BOTTOM MOLDING (N) into the holes in the BOTTOM (D). Wipe away the e ...

METAL BRACKETS on the TOP MOLDING and into the TOP. Fasten four METAL BRACKETS (4G) to the TOP MOLDING (K). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the BRACKETS are even with the edge of the TOP MOLDING (K). Fasten two TIE PLATES (3G) to the TOP MOLDING (K). Use two ...

Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it “square”. Fasten the BACK (F) to your unit using the NAILS (1N). NOTE: Be sure to tap NAILS into the holes that line up over the SHELF (E). Do not stand the unit upright without the BACK ...

BLACK 1/2" FLAT HEAD SCREW (12 used in this step) 11S H H 13H 13H ...

Set the ROD (P) onto the ROD HANGERS on the ENDS (A and B). Fasten the DOOR (H) to the LEFT END (B). Use the screws in the HINGES. NOTE: You may need to loosen the mounting screw to slide the HINGE slightly out of the slot. Retighten the screw before mounting the HINGE to the END. Fasten a PULL (52K) to the DOOR (H). Use a BLACK 1-1/8" MACHINE SCREW (21S). Repeat thi ...

(vertical adjustment) Adjusting screw (horizontal) Refer to the enlarged diagram to identify the parts on the HINGES. The DOORS may need some adjustments. Follow the text below to make needed adjustments. DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw ...