Samsung DVD-CM250 Instruction Manual

DVD-VCR DVD-CM250 www.samsungvcr.com PAL EJECT REC S.MODE STANDBY/ON PHONES COPY PROG SELECT VOL P.SCAN Instruction Manual GB ...

5 I Disc Type and Characteristics ................................................................................................. 6 N DVD-VCR OVERVIEWS I Front View of the DVD-VCR .................................................................................................... 7 I Rear View ...

30 I Recording a Programme with Automatic Stop ......................................................................... 31 I Using the Timer Programming Feature.................................................................................... 32 I Checking a Preset Recording ............................................. ...

Important Note 1 This manuel is divided into two sections: one describing the VCR; the other, the DVD. Prior to undertaking anything, please verify in which section you actually are by checking either the or symbols or the header of the chapter. DVD VCR This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other in ...

DO NOT OPEN THE DVD-VCR. Refer to service personnel. H H 5°C 40°C 10% 75% THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS Do NOT expose the DVD-VCR to extreme temperature condi- tions (below 5°C and above 40°C) or to extreme humidity conditions (less than 10% and more than 75%). Do NOT expose the DVD-VCR to direct sunlight. Do NOT e ...

This DVD player is capable of playing the following types of discs with the corresponding logos : * DO NOT play CD-ROM, VCD, CD-I and DVD-ROM in this player! (CDGs play audio only, not graphics.) * It may not be to play CD-R,CD-RW and DVD-R in all cases due to the type of disc or condition of the recording. Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play ...

7 GB Rear View of the DVD-VCR 1 DVD DECK 2 DVD OPEN/CLOSE 3 VCR DECK 4 VCR EJECT 5 STANDBY/ON 6 HEADPHONE JACK 7 STOP 8 REW/SKIP BACK BUTTON 9 PLAY/STILL 10 F.F/SKIP NEXT BUTTON 11 RECORD 12 SOUND MODE 13 COPY 14 FRONT PANEL DISPLAY 15 PROGRAMME / 16 PROGRESSIVE SCAN 17 SELECT DIAL 18 VOLUME DIAL EJECT REC S.MODE STANDBY/ON PHONES COPY PROG SELECT VOL P.SCAN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 ...

1 STANDBY/ON 2 SHUTTLE<< / >> 3 ANGLE/IPC 4 DVD SELECT 5 VCR SELECT 6 TV VOLUME 7 OPEN/CLOSE, EJECT 8 EZ VIEW 9 REWIND, SKIP BACK 10 STOP 11 DISC MENU 12 MENU 13 LEFT 14 RECORD 15 TEST 16 SPEAKER 17 TV/VCR 18 MODE, REPEAT 19 TITLE, SPEED 20 TV STANDBY/ON 21 0-9 22 ZOOM, INPUT SELECT 23 TV SELECT 24 FM/AM SELECT 25 AMP VOLUME 26 PROG/TRK ( , ) 27 AUDIO 28 MUTE 29 FAST-FORWARD, SKIP NEXT 30 PLAY/STILL 31 CLEAR 32 RETURN, ...

7 8 9 10 1 The DVD Deck is active. 2 DVD or CD media is loaded. 3 The time, counter position, time remaining or current deck status is indicated. 4 Recording is in progress (normal and timer). 5 VHS videotape is loaded. 6 The VCR Deck is active. 7 A DVD with a DTS soundtrack is loaded. 8 The Hi-Fi track of a VHS ...

You must take into account various factors when connecting audio or video systems: N Types of connectors available on your systems N Systems connected permanently to the DVD-VCR (satellite receiver for example) or temporarily (camcorder for example) Your DVD-VCR is equipped with the following connectors. Connector Location Type Direction Recommended Use AV1 (EURO AV) Rear SCART In/Out N Television N Satellite receiver ...

R L Connecting DVD-VCR to the TV using the Coaxial Cable Connecting DVD-VCR to the TV using the SCART Cable To receive television programmes a signal must be received from one of the following sources: N An outdoor aerial N An indoor aerial N A cable television network N A satellite receiver ☛ Make sure that both the television and the DVD-VCR are switched off before connecting the cables ...

1. AV2 IN: By means of 21-pin Scart Cable Plug the SCART Cable with satellite receiver or other equipment into the AV2 (DEC./EXT.) socket on the rear of the DVD-VCR. After making this connection, select the source by pressing the INPUT SEL. button for the AV2 input sources. 2. By means of RF Coaxial Cable After making this connection, you must preset the station received through the satell ...

Your DVD-VCR will automatically set itself up when it is plugged into the mains for the first time. TV stations will be stored in memory. The process takes a few minutes. Your DVD-VCR will then be ready for use. 1 Connect the coaxial cable as indicated on page 11. (Connecting Your DVD-VCR to the TV Using the Coaxial Cable) 2 Plug the DVD-VCR into the mains. Result: The Language Set menu is displayed. 3 Select the required language ...

2 4 You must tune your television for the DVD-VCR only if you are not using a Scart cable ➢ To view pictures from your DVD-VCR when a Scart cable is used, the television must be set to the audio/video mode (AV). 1 Switch on the television. 2 Switch on the DVD-VCR by pressing STANDBY/ON on the front of the DVD-VCR or STANDBY/ON on the remote control. 3 Select a programme position on the television to be reserve ...

The DVD-VCR uses one set of controls to operate both decks. The following keys are helpful in successfully controlling each deck. 1 STANDBY/ON Button Press the STANDBY/ON button on the remote control or front panel to turn on the DVD-VCR. 2 DVD Button Press the DVD button on the remote control when you want to control the DVD deck. N The DVD indicator will light on the Front Panel Display to show that the DVD deck is selected. 3 VCR ...

You must insert or replace the batteries in the remote control when you: N Purchase the DVD-VCR N Find that the remote control is no longer working correctly 1 Push the tab in the direction of the arrow to release the battery compartment cover on the rear of the remote control. 2 Insert two AAA, RO3 or equivalent batteries, taking care to respect the polarities: N + on the battery with + on the remote control ...

The DVD-VCR allows you to copy the contents of a DVD to a VHS tape with a press of the COPY button. If the DVD you are attempting to copy is copy protected, you will not be able to copy the disc. It is not permitted to copy Macrovision® encoded DVDs. 1 INSERT DISC Insert the disc you wish to copy in the DVD deck and close the drawer. 2 Insert VHS Tape Insert a blank VHS videotape into the VCR deck. 3 Copy the DVD to VHS Tape ...

1 Open “MENU” After pressing the MENU, press the OK or ❿. 2 Select “Language” Use the ›or ❷buttons to highlight “Language,” then press the OK or ❿. 3 Set menu Language Place the selection arrow next to your desired Language, then press the OK button. 4 On completion, press RETURN twice to exit the menu. Language : English User Set Auto Power Off : Off Screen Messages : ...

☛ You do not need to preset the stations if you have already set them automatically (see Plug & Auto Set Up on page 13). Your DVD-VCR contains a built-in tuner used to receive television broadcasts. You must preset the stations received through the tuner. This can be done: N Plug & Auto Set up (see page 13) N Automatically N Manually (see page 20) You can store up to 80 stations. 1 After pressing the MENU, pre ...

have already set them automatically. 1 After pressing the MENU, press the OK or ❿. Result: The Setup menu is displayed. 2 Press the corresponding › , ❷buttons to select the Install option. 3 Press the OK or ❿to select this option. Result: The Install menu is displayed. 4 Press the corresponding › or ❷buttons, until the Manual Setup option is selected. 5 Press the OK or ❿to select a Man ...