Ferroli 30800009 Installation & User's Instructions

Radio Thermostat Clock Part Number: 30800009 Installation & User Instructions ...

  *     %    %      12           %   3   3  4  5       $ 2 2 ...

The Radio Thermostat Clock is a 7 day radio frequency (RF) wireless thermostat/ timer which communicates with a special receiver designed to replace the universal digital timer fitted to most of Ferroli’s combination boilers. The Radio Thermostat Clock is battery powered and can be sited wherever conventional room thermostats would normally be sited. In combination with the Radio Th ...

  "  # $ % & $    5 2$   " '  " "7 18' ? 78' 1 1',@+ (   !%   #   1 ,@+#  ,@   )7% 1    11 2 8 %    1 #  1+       ) 4 ...

Domina, Modena and Falcon (MF02) Step 1 Remove clock from control panel. Step 2 Swap wiring as shown. Make sure Live is connected to terminal 1 (wire colour is not conclusive of polarity) Step 3 Fit receiver into control panel. Note. If the Radio thermostat clock is going to replace the existing room thermostat this must be linked out on the room thermostat terminal block. Radio Thermostat Clock Receiver Universal Digital Clock 4 3 2 1 5 3 ...

Step 1 Remove clock from control panel. Step 2 Swap wiring as shown. Make sure Live is connected to terminal 1 (wire colour is not conclusive of polarity) Step 3 Fit receiver into control panel. Domicompact Range Radio Thermostat Clock Receiver Universal Digital Clock 4 3 2 1 5 3 2 1 Note. If the Radio thermostat clock is going to replace the existing room thermostat this must be linked out on the room thermostat terminal block. R ...

Step 2 Swap wiring as shown. Step 3 Fit receiver into control panel. Maxima 35C Step 1 Remove the boiler front cover and lower the control box. Step 2 Remove the terminal block cover. Step 3 Cut off connect block bare back wires approx. 7mm and connect brown to terminal 1 and blue to terminal 3 on the outlet side of the block. Step 4 Connect brown and blue onto receiver terminals 1 and 2. Make sure live i ...

Step 1 Remove boiler outer case and lower control box. Step 2 Remove control box cover. Step 3 Connect brown and blue JST plug onto PCB terminal block X2. Step 4 Connect brown and blue onto receiver terminals 1 and 2. Make sure live is connected to terminal 1. (the wire colour is not conclusive of polarity). Step 5 Connect the two grey wires to terminal 3 and 4 on the receiver. On the main boiler terminal block remove link wire from termi ...

If no valid radio signal is received from the receiver for more than 1 hour, emergency running mode is activated. ED value 12.8 minutes, switch-on time 30%. See page 16. Radio link installation 1. Install transmitter and select continuous radio operation system mode. (See page 17) 2. Press receiver button and hold down for 2 seconds. The LED flashes twice. Then release the button. The LED ...

 0       ?  ?   > 3   3  34   5  3 5      10 ...

  +  ( +  A >  > :   127  8)(&  (#               2 / ! > ..))',.))'3 >.0.))'6.))- )))')))'7':     8 >,..))'+.))'5   >+.3     > >  >+ :: ) (2 "   +  12 ...

"   +  /  C3 9.'0.,  C390.,'.,  C3 9.,'.  C9: :   1: ) %  :   ,   0),  C9: :   1: ) %  :     ),)  / 3     ), 0),1: :  C9:  )  ...

) + *       .   A  #      )!   : 2)     : :      2)2 1 1  :2      ) + *   +        + "        ) ) + *  (   (     ...

) +   -  - )  %      :   : ) 15 ...

)"  * )"   %    : 2)      / 1    )   1)     +   "  ,&  ))7   #   8  ,%   )7    8  ,$  ))7 1   8 &*  : 1   )   ...

'=%    '=>    !% $&&:    :' ) '=    17 ...

                                    ! " # " $ # % &  # '( ' #   )*& +,* -. !/.0 . !/., 80.10.1144.7/07/01 ...