Fisher 657 Instruction Manual

Text of the manual

Fisher 657 Diaphragm Actuators

Size 80 and 100 Contents Introduction 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scope of Manual 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications 3 . . . . . . . . . . . . . . . . .

657 Size 80 and 100 Actuators

December 2010 2 Table 1. Specifications SPECIFICATIONS ACTUATOR SIZE 80 100 Nominal Effective Diaphragm Area cm2 1761 2902 inch2 273 450 Yoke Boss Diameters mm 127 127 178 inch 5 5H(1) 7 Acceptable Valve Stem Diameters mm 25.4 or 31.8 31.8 50.8 inch 1 or 1‐1/4 1‐1/4 2 Maximum Allowable Output T

657 Size 80 and 100 Actuators

December 2010 3 handwheel may be used as an auxiliary manual actuator. A side‐mounted handwheel assembly is normally used as an auxiliary manual actuator. Specifications Refer to table 1 for specifications of the 657 actuator. See the actuator nameplate for information about a specific actuator.

657 Size 80 and 100 Actuators

December 2010 4 2. Screw valve stem locknuts (key 16, figure 4) all the way onto valve stem thread. 3. Connect an air supply to the diaphragm casing. 4. For push‐down‐to‐close valves, be sure the valve plug is on its seat. Apply pressure to ensure that the actuator stem is fully extended.

657 Size 80 and 100 Actuators

December 2010 5 When adjusting travel of a reverse‐acting (push‐down‐to‐open) valve, apply a slight pressure on the actuator diaphragm. This moves the valve plug off the seat, reducing the chance of damaging the valve plug or seat during adjustments. 1. Back the stem locknuts away from the

657 Size 80 and 100 Actuators

December 2010 6 Figure 3. Dimension B for Spring Adjustment LOWER DIAPHRAGM CASING SPRING SEAT JAM NUT ADJUSTING NUT A0950‐1 B For small spring forces, adjustments can be made by rotating the adjusting nut (key 114, figure 5). Clockwise rotation (when viewed from diaphragm casings) of the adjust

657 Size 80 and 100 Actuators

December 2010 7 tools away from the spring and spring seat, slowly decrease loading pressure until the spring force holds the spacers firmly between the spring seat and lower diaphragm casing (key 5, figure 5). 5. Loosen the jam nut. The adjusting nut can now be rotated clockwise (when viewed from

657 Size 80 and 100 Actuators

December 2010 8 WARNING To avoid personal injury from the precompressed spring force thrusting the upper diaphragm casing (key 1) away from the actuator, relieve spring compression (step 2, below), and carefully remove casing cap screws (key 22) (step 4, below). 2. Remove cover band (key 60). In

657 Size 80 and 100 Actuators

December 2010 9 3. Position the lower spring seat (key 11), and slide the actuator spring (key 6) squarely onto the spring seat. 4. If the diaphragm plate and actuator stem (keys 4 and 10) were separated, fasten them together using the cap screw (key 3) and tighten to a torque of 544 Nm (400 lbf

Other Automobile Parts Manuals