Flymo Sabre Trim Owner's Manual

& retain for future reference For all customer enquiries or for replacement parts, contact:- ☎ 01325 300303 www.flymo.com [email protected] Sabre Trim ...

IF ANY PARTS ARE MISSING CONTACT:- Husqvarna Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this product can be dangerous! This product can cause serious injury to the opera- tor and others, the warnings and safety instructions must be followed to ensure reasonable ...

instructions to use the product. Local regulations may restrict the age of the operator. 2. Only use the product in the manner and for the functions described in these instructions. 3. Never operate the product when you are tired, ill or under the influence of alcohol, drugs or medicine. 4. The operator or user is responsible for accidents or hazards occurring to other people or their prop- er ...

Attatching the Trimmer Head to the Sabre Handle 1. Push the Trimmer Head onto the Sabre Handle until you hear a click. (E1) 2. Push the Trimmer Head further onto the Sabre Handle until it reaches the mark shown in Fig E2. 3. Turn the Trimmer Head collar until it is secure. (E3) E2 E1 To adjust the Sabre handle length 1. Loosen the Sabre Handle collar. (G1) 2. Adjust length of the handle to the most comfortable operating positi ...

H line cutter How the automatic line feed works (H) 1. When initially switching on the trimmer, a small length of line is fed out. 2. A ‘clattering’ noise will be heard when the nylon line hits the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. • Make sure the motor is up to full speed before ...

• WARNING • The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. • BEFORE USE Make sure that the cutting line is fed out. • Make sure motor is up to full speed before trim- ming or edg ...

1. Press and hold in the two cap release latches. (T). 2. Pull cap away from the spoolholder. (T). When refitting the spool cap 1. Keep all areas of the cap and spoolholder clean. Failure to do so may prevent the cap being securely located in the spoolholder. 2. Replace the cap, pressing firmly DOWN towards the spoolholder to ensure cap is fully located. 3. Check that the cap is correctly fitted by trying to remove it witho ...

mer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. Caring for your product After you have finished using your product follow the pro- cedure below: 1. Never clean your trimmer with water, cleaning fluids, or solvents, just remove debris with a suitable tool, a soft brush or dry cloth. 2. Using a soft brush, clean around the insi ...

FAULT CHECK ACTION Is the automatic line feed work- ing? Manually feed out line. SEE “MANUAL LINE FEED” Is the line fed out and visible? Has line been removed from cleat? Remove cap and spool, free line and re-fit spool and cap. SEE “CUTTING HEAD” The line may be jammed on the spool. Rewind line to remove crossed loops. Check that line is in correct section of spool. Is the manual line feed working? Has too much line been fed ...

Aycliffe Industrial Park NEWTON AYCLIFFE Co.Durham DL5 6UP ENGLAND Telephone - (00) 44 1325 300303 Fax - (00) 44 1325 310339 UK Customer Helpline - 01325 300303 Fax - 01325 310339 Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. If any part is found to be defective due to faulty manufacture within the guarantee period, Husqvarna Outd ...