TRENDnet TEW-638PAP Operation & User’s Manual

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause ha ...

Radio products with the CE marking comply with the R&TTE Directive (1999/5/EC), the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: z EN 60950 Product Safety z EN 300 328 Technical requirement for radio equipment z EN 301 489-1/-17 General EMC requirements for radio equipment ...

authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed inform ...

požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede TRENDware erklærer herved, at følgende udstyr TEW-638PAP overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt TRENDware, dass sich das Gerät TEW-638PAP in Übereinstimmung mit den grundlegenden Anfo ...

Minimum System Requirements ............................................................................................................... 7 Introduction .............................................................................................................................................. ...

z CAT-5 Ethernet Cable (the TEW-638PAP’s Ethernet ports is Auto-MDIX) z Power Adapter (12.0V, 0.5A) z CD-ROM with Manual & Wizard z Quick Installation Guide Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product. Minimum System Requirements Installation Requirements • Web Browser: Internet Explorer (6 or higher) Mozilla ...

n network or to connect a wired device to an existing wireless network. Use multiple 300Mbps Wireless N Access Points together to extend your network using Wireless Distribution System (WDS), Wireless Bridge and AP Client Modes. Expand a wireless network without running additional cabling with Wireless Distribution Service (WDS) technology by con ...

This port automatically senses the cable type when connecting to Router. Reset Button Pressing the reset button restores the AP to its original factory default settings. Power Switch (EU version) On/off Switch DC-IN The DC power input connector is a single jack socket to supply power to the TEW-638PAP. Please use the Power Adapter provided on the TEW-638PAP package. Power Switch EU Version ...

is ready. This LED blinks green during wireless data transmission. WPS LED This LED blinks green during WPS function is enabled. LAN LED A solid light indicates a connection to a Router on the LAN port. This LED blinks green during data transmission POWER LED A solid green light indicates a proper connection to the power supply WPS Button Press the button to enable WPS function. 10 ...

1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at an angle. The more material the signal has to pass through the more signal you will lose. 2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will mi ...

1. Insert Setup Wizard CD into your CD-ROM drive. 2. The Welcome screen appears on your monitor. Click Setup Wizard button. 3. Read the License Agreement and click Next to continue the installation. 4. Connect an Ethernet cable from the LAN port on your Router to the LAN port on the TEW-638PAP, click Next button to continue. Page 12 ...

connecting together. Verify the Power & Ethernet LEDs are light. EU Version please make sure the power switch is on the On position 5. Your computer will detect TEW-638PAP and the Device List screen appears on your monitor. Click Configure button to continue (default TEW-638PAP IP Address is 192.168.10.100). 6. Enter password for the Access Point. The default password is ...

Point” and click Next to continue 2. To attain an IP address automatically, you can select “Dynamic IP address configuration”; to change IP address, you can select “Static IP address configuration” and click Next button to continue. 3. The default IP address is 192.168.10.100, you can choose to obtain network setting automatically, o ...

button. 5. Use Push Button Method, click Connect button to continue. You also need to enable WPS function of the wireless client device to make connection. 6. Use PIN Method and enter your wireless client PIN number on Wireless Device PIN, and then click Connect button to make wireless connection. Page 15 ...

8. Enter SSID of TEW-638PAP, click Next button. 9. Choice Wireless Mode. Page 16 ...

11. To use WEP security, select WEP and click Next button. Select 64-bit or 128-bit WEP key length, and enter your WEP key. For 64-bit encryption, enter 10 hexadecimal characters, For 128-bit encryption, enter 26 hexadecimal characters. Click Next to continue the setting. 12. To use WPA or WPA2 security, select WPA or WPA2 and click Next button. Select WPA Mode: WPA Only, WPA2 Only, WPA or WP ...

the Save or Print buttons. Once finished, click Configure to continue. 14. Save you setting to a text file in a desired location. 15. Congratulations you have configured you TEW-638PAP. Page 18 ...

2. Insert Setup Wizard CD into your CD-ROM drive. 3. The Welcome screen appears on your monitor. Click Setup Wizard button. 4. Read the License Agreement and click Next to continue the installation. 5. Connect an Ethernet cable from the LAN port on your Router to the LAN port on the TEW-638PAP, click Next button to continue. Page 19 ...

connecting together. Verify the Power & Ethernet LEDs are light. EU Version please make sure the power switch is on the On position 7. Your computer will detect TEW-638PAP and the Device List screen appears on your monitor. Click Configure button to continue (default TEW-638PAP IP Address is 192.168.10.100). Page 20 ...